4821 Chelsea Avenue Kansas City, MO (800) (CHEMTREC)

Transkriptio

1 OLYBOND PART Product Name OlyBond500 - Part Product Identifier Recommended Use Restrictions Manufacturer Address SECTION IDENTIFICATION One component of a two-component polyurethane system Foam Adhesive None DERBIGUM Americas, Inc 482 Chelsea Avenue Kansas City, MO 6430 Phone Number (800) Emergency Number (800) (CHEMTREC) GHS Classification Acute Toxicity, Inhalation: Hazard Category 4 Respiratory Sensitization: Hazard Category Skin Sensitization: Hazard Category Skin Irritation: Hazard Category 2 Eye Irritation: Hazard Category 2A Specific Target Organ Toxicity, Single Exposure: Hazard Category 3 Specific Target Organ Toxicity, Repeated Exposure: Hazard Category 2 Hazard Pictographs SECTION 2 HAZARDS Signal Word Hazard Statements Precautionary Statements Danger H37 - May cause an allergic skin reaction H39 - Causes serious eye irritation H334 - May cause allergy or asthma symptoms or breathing difficulties if inhaled H372 - May cause damage to organs (central nervous system, eye, skin, lung, liver) through prolonged or repeated exposure (dermal, inhalation) P20 - Obtain special instructions before use P202 - Do not handle until all safety precautions have been read and understood P233 - Keep container tightly closed P240 - Ground/bond container and receiving equipment P260 - Do not breathe fume, gas, vapors P264 - Wash hands, forearms and face thoroughly after handling P270 - Do not eat, drink or smoke when using this product P273 - Avoid release into the environment P280 - Wear protective gloves and clothing P303+P36+P353 - If on skin (or hair), Take off immediately all contaminated clothing. Rinse skin with water/shower P303+P340 - If inhaled: remove person to fresh air and keep comfortable for breathing P305+P35+P338 - If in eyes: rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing P308+P33 - If exposed or concerned, get medical advice/attention P34 - Get medical advice/attention if you feel unwell P32 - Specific treatment (see eye protection, protective gloves P370+P378 - In case of fire: Use carbon dioxide (CO2), foam, dry extinguishing powder to extinguish

2 OLYBOND PART SECTION 2 HAZARDS P403+P235 - Store in well-ventilated place. Keep cool P405 - Store locked up P50 - Dispose of contents/container to a licensed hazardous-waste disposal contractor or collection site except for empty clean containers which can be disposed of as non-hazardous waste SECTION 3 COMPOSITION Chemical Composition Polymeric Isocyanates 4,4 -Methylene Bisphenyl Isocyanate Diphenylmethane Diisocyanate Mixed Isomers CAS NUMBER PERCENT BY WEIGHT Note: The above components and their percentages are provided for health and safety purposes, ONLY. This document should not be construed as a guaranteed analysis of any specific lot or as specifications for the product. <0 SECTION 4 FIRST AID MEASURES First-Aid, Eyes First-Aid, Skin First-Aid, Inhalation First-Aid, Ingestion Immediate Medical Attention Hold eyes open and flush with lukewarm water for at least 5 minutes. Seek immediate medical assistance. Remove contaminated clothing and wash with soap and water. Wash affected areas with soap and water for at least five minutes. If irritation persists or a rash occurs, seek medical attention. Launder or dry-clean clothing before reuse. If signs and symptoms of respiratory toxicity are observed, remove subject from area and seek immediate medical attention. Keep the subject warm and at rest. If necessary, administer oxygen or perform artificial respiration if necessary and qualified personnel are available to do so. Do not induce vomiting aspiration hazard. If the subject is conscious, wash mouth and give 2 or more cups of milk or water. Seek immediate medical assistance. Do not attempt to give anything by mouth to an unconscious or convulsive person. Inhalation exposure can irritate the respiratory tract and induce respiratory sensitization. Treatment of acute irritation and bronchial constriction should be done according to symptoms. Eye contact can cause moderate to severe irritation. Skin contact can cause moderate irritation, and may elicit an allergic response among susceptible individuals. Treat eye and skin irritation or injury according to symptoms. Extended medical treatment may be necessary for individuals exhibiting respiratory sensitization and/or skin disorders. SECTION 5 FIRE FIGHTING MEASURES Flash Point 484 F (220 C) LEL: Not determined UEL: Not determined Hazardous Products of Combustions Extinguishing Media Explosion Hazard Protection Gear Combustion products may include carbon monoxide, oxides of nitrogen, organic isocyanates, and hydrogen cyanide. Water spray, carbon dioxide, dry chemical or chemical foam. DO NOT use water jet. This product may ignite if exposed to sources of ignition at temperatures in excess of its flash point. If fighting a fire in which this product is present, wear a self-contained breathing apparatus with full-facepiece operated in pressure-demand or other positive pressure mode.

3 OLYBOND PART SECTION 6 ACCIDENTAL RELEASE MEASURES Personal Precautions Environmental Precautions Method and Materials for Containment & Clean Up Avoid contact with skin, eyes, and mucous membranes. Wear appropriate personal protective equipment (see Section #8) during cleanup and decontamination. Restrict unauthorized personnel during cleanup and disposal operations. Prevent spills from entering sewers or contaminating soil. Report releases as required by local, state and federal authorities. Absorb spilled material with a sorbent such as sawdust or calcium silicate hydrate. When absorbed, transfer to an impervious container. Neutralize with solution of 8-0% sodium carbonate and 2% liquid detergent in water (0: ratio of solution to product). Do not seal container, as CO2 will be released. Neutralize in a well ventilated area for at least 48 hours before sealing containers for disposal. SECTION 7 HANDLING AND STORAGE Work and Hygiene Practices To prevent ingestion or contact following use of the product, wash hands and face before eating, drinking, applying cosmetics, or using tobacco. Remove contaminated clothing and protective equipment before entering eating/drinking areas. Handling Containers should be kept tightly closed to prevent contact with moisture and other chemicals. Do not reuse empty containers for any purpose. When handling the product, avoid contact with eyes, skin, and clothing, using protective equipment as needed. Do not use this product around children, and secure it away from children. Storage Keep containers properly sealed in a cool, dry, well-ventilated area between F ( C). Do not store in open, unlabeled or mislabeled containers. Do not reuse empty container without commercial cleaning or reconditioning. SECTION 8 EXPOSURE CONTROLS AND PERSONAL PROTECTION Eye Skin Respiratory Ventilation Occupational Exposure Limits Wear eye protection adequate to prevent eye contact with the product. Plastic-frame spectacles with side shields, chemical goggles, or a face shield are recommended. Do not wear contact lenses when working with this product. Wear protective gloves and clothing to prevent skin irritation or injury from contact with the product. Glove materials known to be effective against permeation by isocyanates include butyl rubber, nitrile rubber, and polychloroprene. If an exposure level to a component exceeds an applicable standard, use a NIOSH approved respirator of a class and configuration effective for protection from the component(s) generated. Where exposures exceed the OSHA Permissible Exposure Limit (PEL), an airline respirator or self-contained breathing apparatus (SCBA) is recommended. Consult OSHA regulations (29CFR90.34) and/or American National Standard Z88.2 (ANSI, New York, NY 0036, USA) for guidance. Use appropriate ventilation (dilution or local exhaust) whenever natural ventilation is restricted or inadequate to maintain concentrations of all components within their applicable standards. CAS NUMBER OSHA PEL ACGIH TLV NIOSH REL Polymeric Isocyanates Not Established Not Established Not Established 4,4 -Methylene Bisphenyl Isocyanate Diphenylmethane Diisocyanate Mixed Isomers ppm Ceiling Not Established ppm TWA Not Established 0.05 mg/m 3 TWA 0.2 mg/m 3 Ceiling (0 min) Not Established

4 OLYBOND PART SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES Physical State Liquid Appearance Dark brown liquid Odor Aromatic ph Boiling Point: 200 F (93 C) Melting Point Flash Point 484 F (220 C) Flammability Class IIIB Vapor Pressure Vapor Density Evaporation Rate VOC (per EPA Method 24).00 grams/liter Relative Density.22 Solubility in Water Reacts with water Oil-water Partition Coefficient Decomposition temperature Viscosity cps SECTION 0 STABILITY AND REACTIVITY Stability Incompatibility Hazardous Decomposition Hazardous Polymerization Stable at room temperature Water, alcohols, acids, alkalis, and amines Carbon monoxide, carbon dioxide, nitrogen oxides, isocyanates, and hydrogen cyanide May occur at temperatures >392 F (200 C) SECTION TOXICOLOGICAL INFORMATION Component Analysis CAS NUMBER LD50 ORAL LD50 DERMAL LC50 INHALATION 4,4 -Methylene Bisphenyl Isocyanate >5,000 mg/kg (rat) Not Available 2,240 mg/m 3 for hour (rat) Diphenylmethane Diisocyanate Mixed Isomers >5,000 mg/kg (rat) Not Available 2,240 mg/m 3 for hour (rat) Primary Route(s) of Entry Eye Hazards Skin Hazards Ingestion Hazards Inhalation Hazards Inhalation; ingestion This product may cause moderate to severe eye irritation. This product may cause mild to moderate skin irritation and has the potential to cause skin sensitization among susceptible individuals. The product is nontoxic by ingestion, but ingestion may cause nausea, vomiting, and/or gastrointestinal irritation. Inhalation of toxicologically-significant quantities of ingredients is unlikely when the product is used in a well-ventilated area and in accordance with instructions.

5 OLYBOND PART SECTION TOXICOLOGICAL INFORMATION Symptoms Related to Overexposure Delayed Effects from Long-Term Overexposure Carcinogenicity Germ Cell Mutagenicity Reproductive Toxicity: Inhalation overexposure to isocyanates may cause respiratory irritation, breathing difficulties, and asthma-like symptoms. Long-term inhalation overexposure to this product may result in respiratory sensitization, which may be irreversible. A single inhalation study exposing rats to aerosolized polymeric 4,4 -Methylene Bisphenyl Isocyanate identified a single malignant pulmonary tumor among 60 animals exposed at the highest exposure level. Observations of pulmonary fibrosis and other pathological anomalies in the test animals precluded definitive determination as to the cause(s) of the tumor. Epidemiological studies of humans occupationally exposed to the isocyanates in this product have found no strong association or consistent pattern with respect to carcinogenicity. No ingredients have been determined to be germ cell mutagens. No ingredients have been determined to be damaging to fertility or to the unborn child. SECTION 2 ECOLOGICAL INFORMATION Eco toxicity Ozone Depletion Potential Diphenylmethane Diisocyanate Mixed Isomers: Aquatic Toxicity to Fish: LC50 >,000 mg/l for 96 hours (zebra fish) Aquatic Toxicity to Invertebrates: EC50 >,000 mg/l for 24 hours (daphnia) Aquatic Toxicity to Plants: EC50 >,640 mg/l for 72 hours (algae) Aquatic Toxicity to Microorganisms: EC50 >00 mg/l for 3 hours (bacteria) Toxicity to Terrestrial Organisms: NOEC=,000 mg/kg for 4 days (worms) for Persistence and Degradability, Bioaccumulation Potential, or Mobility in Soil. Polymeric Isocyanates: for Aquatic Toxicity to Fish, Invertebrates, Plants, or Microorganisms, Toxicity to Terrestrial Organisms, Persistence and Degradability, Bioaccumulation Potential, or Mobility in Soil. This product neither contains nor is manufactured with any ingredients known to deplete the ozone layer. SECTION 3 DISPOSAL CONSIDERATIONS Disposal Instructions Do not discharge waste product into sanitary or storm sewers or allow it to contaminate soil. Empty containers should be decontaminated prior to disposal. Consult applicable Federal, State/Provincial, and local regulations. See Section 7 for Handling Procedures. See Section 8 for Personal Protective Equipment recommendations. SECTION 4 TRANSPORT INFORMATION US DOT Information TDG Information Not regulated as a hazardous material. Not regulated as a dangerous good.

6 OLYBOND PART SECTION 5 REGULATORY INFORMATION TSCA Inventory Sara 33 Sara 3/32 Categories CERCLA CA Proposition 65 Right to Know States All ingredients of this product are listed This product contains these ingredients in concentrations % (for carcinogens 0.%) regulated under Section 33 of the Emergency Planning and Community Right-To-Know Act of 986 or 40 CFR 372:. 4,4 -Methylene Bisphenyl Isocyanate (CAS ) 2. Polymeric Isocyanates (CAS ) Acute Health Hazard; Chronic Health Hazard, Reactivity Hazard Under requirements of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), 4,4 -Methylene Bisphenyl Isocyanate (CAS ) has a Reportable Quantity of 5,000 lbs. Any spill or release above this RQ must be reported to the National Response Center ( ). This product does not contain chemicals known to the state of California to cause cancer, birth defects, and/or other reproductive harm. CAS NUMBER CA MA MN MN PA RI 4,4 -Methylene Bisphenyl Isocyanate Polymeric Isocyanates Diphenylmethane Diisocyanate Mixed Isomers No No No No No No Canadian Regulatory Information This product has been classified in accordance with Canada s Hazardous Products Regulations (SOR/DORS/205-5). SECTION 6 OTHER INFORMATION This material has been defined as a hazardous chemical under the criteria of the OSHA Hazard Communication Standard (29 CFR ). NFPA Rating HMIS Rating HEALTH 2 2 The information and recommendations contained herein are to the best of DERBIGUM Americas knowledge and belief, accurate and reliable as of the date issued. DERBIGUM Americas does not warrant or guarantee their accuracy or reliability, and DERBIGUM Americas shall not be liable for any loss or damage arising out of the use thereof. The information and recommendations are offered for the users consideration and examination, and it is the user s responsibility to satisfy itself that they are suitable and complete for its particular use. It is also the users responsibility to make certain that it is relying upon the most recent, updated, information and recommendations available from DERBIGUM Americas. The Environmental Information included, as well as the Hazardous Material Identification System (HMIS) and National Fire Protection Association (NFPA) ratings, have been included by DERBIGUM Americas in order to provide additional health and hazard classification information. The ratings recommended are based upon the criteria supplied by the developers of these rating systems, together with DERBIGUM Americas interpretation of the available data. FIRE 2 REACTIVITY Reason for revision: Solvent Change & updated hazard information

7 OLYBOND PART 2 Product Name OlyBond500 - Part 2 Product Identifier Recommended Use Restrictions Manufacturer Address SECTION IDENTIFICATION One component of a two-component polyurethane system Foam Adhesive None DERBIGUM Americas, Inc 482 Chelsea Avenue Kansas City, MO 6430 Phone Number (800) Emergency Number (800) (CHEMTREC) SECTION 2 HAZARDS GHS Classification Hazard Pictographs Eye Irritation: Hazard Category 2B Specific Target Organ Toxicity, Repeated Exposure: Hazard Category 2 Signal Word Hazard Statements Precautionary Statements Warning H39 - Causes serious eye irritation H334 - May cause allergy or asthma symptoms or breathing difficulties if inhaled H372 - May cause damage to organs (central nervous system, eye, skin, lung, liver) through prolonged or repeated exposure (dermal, inhalation) P20 - Obtain special instructions before use P202 - Do not handle until all safety precautions have been read and understood P233 - Keep container tightly closed P240 - Ground/bond container and receiving equipment P260 - Do not breathe fume, gas, vapors P264 - Wash hands, forearms and face thoroughly after handling P270 - Do not eat, drink or smoke when using this product P273 - Avoid release into the environment P280 - Wear protective gloves and clothing P303+P36+P353 - If on skin (or hair), Take off immediately all contaminated clothing. Rinse skin with water/shower P303+P340 - If inhaled, remove person to fresh air and keep comfortable for breathing P305+P35+P338 - If in eyes: rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing P308+P33 - If exposed or concerned, get medical advice/attention P34 - Get medical advice/attention if you feel unwell P32 - Specific treatment (see eye protection, protective gloves P370+P378 - In case of fire: Use carbon dioxide (CO2), foam, dry extinguishing powder to extinguish P403+P235 - Store in well-ventilated place. Keep cool

8 OLYBOND PART 2 SECTION 2 HAZARDS P405 - Store locked up P50 - Dispose of contents/container to a licensed hazardous-waste disposal contractor or collection site except for empty clean containers which can be disposed of as non-hazardous waste SECTION 3 COMPOSITION Chemical Composition Diethylene Glycol Dipropylene Glycol CAS NUMBER PERCENT BY WEIGHT Note: The above components and their percentages are provided for health and safety purposes, ONLY. This document should not be construed as a guaranteed analysis of any specific lot or as specifications for the product. <0 <0 SECTION 4 FIRST AID MEASURES First-Aid, Eyes First-Aid, Skin First-Aid, Inhalation First-Aid, Ingestion Immediate Medical Attention Immediately flush with large amounts of potable water. Eye lids should be held away the eyeball to ensure thorough rinsing. Get medical attention if irritation persists. Remove contaminated clothing and wash with soap and water. Wash affected areas with soap and water for at least five minutes. If irritation persists or a rash occurs, seek medical attention. Launder or dry-clean clothing before reuse. If signs and symptoms of respiratory toxicity are observed, remove subject from area and seek immediate medical attention. Keep the subject warm and at rest. If necessary, administer oxygen or perform artificial respiration if necessary and qualified personnel are available to do so. Do not induce vomiting aspiration hazard. If the subject is conscious, wash mouth and give 2 or more cups of milk or water. Seek immediate medical assistance. Do not attempt to give anything by mouth to an unconscious or convulsive person. None of the components of this product are acutely toxic by ingestion or inhalation. Eye contact can cause mild to moderate irritation. Skin contact can cause mild irritation. Ingestion is unlikely to occur in industrial use, but if ingestion occurs it may cause nausea, vomiting, and gastrointestinal irritation. Chronic ingestion can cause kidney injury. SECTION 5 FIRE FIGHTING MEASURES Flash Point/Method 375 F (9 C) LEL: Not determined UEL: Not determined Extinguishing Media Fire and Explosion Hazards Firefighting Instructions Water spray, carbon dioxide, dry chemical or chemical foam. DO NOT use water jet. This product may ignite if exposed to sources of ignition at temperatures above its flash point. If present in a fire or explosion, potential thermal decomposition byproducts include carbon monoxide, smoke, and irritant decomposition byproducts. If fighting a fire in which this product is present, wear a self-contained breathing apparatus with full-facepiece operated in pressure-demand or other positive pressure mode.

9 OLYBOND PART 2 SECTION 6 ACCIDENTAL RELEASE MEASURES Containment Procedures Personal Precautions Environmental Precautions Method and Materials for Containment & Clean Up Wear appropriate personal protective equipment. Stop the flow of material, if this is without risk. Do not allow to drain to sewers. Wear appropriate protective clothing to avoid eye and skin contact. Prevent spills from entering sewers or contaminating soil. Absorb spilled material with a sorbent such as sawdust, vermiculite, or calcium silicate hydrate. When absorbed, transfer to an impervious container. SECTION 7 HANDLING AND STORAGE Handling Work and Hygiene Practices Storage Containers should be kept tightly closed to prevent contact with moisture and other chemicals. Do not reuse empty containers for any purpose. When handling the product, avoid contact with eyes, skin, and clothing, using protective equipment as needed. Do not use this product around children, and secure it away from children. To prevent ingestion or contact following use of the product, wash hands and face before eating, drinking, applying cosmetics, or using tobacco. Remove contaminated clothing and protective equipment before entering eating/drinking areas. Store containers tightly sealed in a dry, well-ventilated, area away from incompatible materials (see Section #0). Recommended temperature range for storage is F. ( C.). SECTION 8 EXPOSURE CONTROLS AND PERSONAL PROTECTION Eye Skin Respiratory Ventilation Occupational Exposure Limits Wear eye protection adequate to prevent eye contact with the product. Plastic-frame spectacles with side shields, chemical goggles, or a face shield are recommended. Do not wear contact lenses when working with this product. Wear protective gloves and clothing to prevent skin irritation or injury from contact with the product. Glove materials known to be effective against permeation by this product include butyl rubber, nitrile rubber, and polyvinyl alcohol. If an exposure level to a component exceeds an applicable standard, use a NIOSH-approved respirator of a class and configuration effective for protection from the component(s) generated. Consult OSHA regulations (29CFR90.34) and/or American National Standard Z88.2 (ANSI, New York, NY 0036, USA) for guidance. Use appropriate ventilation (dilution or local exhaust) whenever this product is used in conjunction with OlyBond 500 Bag in Box Part in conditions where natural ventilation is restricted. ACGIH, OSHA, and NIOSH have not developed exposure limits for any of this product s components. SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES Physical State Appearance Odor ph Boiling Point: Melting Point Liquid Red viscous liquid Mildly sweet

10 OLYBOND PART 2 SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES Flash Point 375 F (9 C) Autoignition Point Flammability Class IIIB Vapor Pressure Vapor Density Evaporation Rate VOC (per EPA Method 24):.00 grams/liter Relative Density.02 Solubility in Water partial Oil-water Partition Coefficient Decomposition Temperature Viscosity cps SECTION 0 STABILITY AND REACTIVITY Stability Reactivity Incompatibility Risk of Dangerous Reactions Hazardous Decomposition Hazardous Polymerization Stable Polymerizes with isocyanate-containing substances Oxidizing agents None reasonably foreseeable Carbon monoxide, carbon dioxide, smoke, and irritant decomposition byproducts Will not occur SECTION TOXICOLOGICAL INFORMATION Ingredients Toxicology Data CAS NUMBER LD50 ORAL LD50 DERMAL LC50 INHALATION Diethylene Glycol ,850 mg/kg (rat),890 mg/kg (hamster) Dipropylene Glycol ,565 mg/kg (rat) >20,000 mg/kg (rabbit) Primary Route(s) of Entry Eye Hazards Skin Hazards Ingestion Hazards Inhalation Hazards Symptoms Related to Overexposure Inhalation; ingestion This product may cause moderate to severe eye irritation. This product may cause mild to moderate skin irritation and has the potential to cause skin sensitization among susceptible individuals. The product is nontoxic by ingestion, but ingestion may cause nausea, vomiting, and/or gastrointestinal irritation. Inhalation of toxicologically-significant quantities of ingredients is unlikely when the product is used in a well-ventilated area and in accordance with instructions. Inhalation overexposure may cause respiratory irritation.

11 OLYBOND PART 2 SECTION TOXICOLOGICAL INFORMATION Delayed Effects from Long-Term Overexposure Carcinogenicity Germ Cell Mutagenicity Reproductive Toxicity Acute Toxicity Long-term inhalation overexposure to this product may result in respiratory sensitization, which may be irreversible. No ingredients are classified as potential or confirmed human carcinogens by OSHA, NTP, or IARC. No ingredients have been determined to be germ cell mutagens. No ingredients have been determined to be damaging to fertility or to the unborn child. L D 50 (oral): >0,000 mg/kg LD50 (dermal): >0,000 mg/kg LC50: no data available Interactive effects of components: no data available SECTION 2 ECOLOGICAL INFORMATION Eco toxicity Ozone Depletion Potential No ecotoxicity data are available for the product or its components. This product neither contains nor is manufactured with any ingredients known to deplete the ozone layer. SECTION 3 DISPOSAL CONSIDERATIONS Disposal Instructions Do not discharge waste product into sanitary or storm sewers or allow it to contaminate soil. Empty containers should be decontaminated prior to disposal. Consult applicable Federal, State/Provincial, and local regulations. See Section 7 for Handling Procedures. See Section 8 for Personal Protective Equipment recommendations. SECTION 4 TRANSPORT INFORMATION US DOT Information TDG Information Not regulated as a hazardous material. Not regulated as a dangerous good. SECTION 5 REGULATORY INFORMATION TSCA Inventory Sara 33 Sara 3/32 Categories CA Proposition 65 Right to Know States Canadian Regulatory Information Components are listed This product contains these ingredients in concentrations % (for carcinogens 0.%) regulated under Section 33 of the Emergency Planning and Community Right-To-Know Act of 986 or 40 CFR 372. Acute Health Hazard, Chronic Health Hazard This product does not contain chemicals known to the state of California to cause cancer, birth defects, and/or other reproductive harm. No components are listed This product has been classified in accordance with Canada s Hazardous Products Regulations (SOR/DORS/205-5).

12 OLYBOND PART 2 SECTION 6 OTHER INFORMATION This material has been defined as a hazardous chemical under the criteria of the OSHA Hazard Communication Standard (29 CFR ). HEALTH FIRE REACTIVITY NFPA Rating HMIS Rating The information and recommendations contained herein are to the best of DERBIGUM Americas knowledge and belief, accurate and reliable as of the date issued. DERBIGUM Americas does not warrant or guarantee their accuracy or reliability, and DERBIGUM Americas shall not be liable for any loss or damage arising out of the use thereof. The information and recommendations are offered for the users consideration and examination, and it is the user s responsibility to satisfy itself that they are suitable and complete for its particular use. It is also the users responsibility to make certain that it is relying upon the most recent, updated, information and recommendations available from DERBIGUM Americas. The Environmental Information included, as well as the Hazardous Material Identification System (HMIS) and National Fire Protection Association (NFPA) ratings, have been included by DERBIGUM Americas in order to provide additional health and hazard classification information. The ratings recommended are based upon the criteria supplied by the developers of these rating systems, together with DERBIGUM Americas interpretation of the available data. Reason for revision: Solvent Change & updated hazard information 0 0