DUPOL KFT HUNGARY SINGULAR WIFI WIFI alarm communicator for signal to smartphone App, working with any alarm panel Connection to alarm panel through Ring/Tip terminals (emulates phone line) Forwards Contact ID report from alarm panel to smartphone App dupol.eu SPDA Online temperature monitoring with adjustable alarm thresholds, and manageable inputs and outputs by smartphone Contact inputs status signalling to mobile App (push notification) Realy control from mobile App with state change authentication Transparent serial port allows to Live stream of remotely program an alarm system temperature values to of any type mobile App and to IoT Two controllable partition by smartphone Supports two WIFI networks, primary and backup access points Long range wireless network(802.11 b/g/n) Configuration and diagnostic in WEB browser through Internet connection Temperature alarm with low and high threshold limits Alarm message acknowledge with authentication Remote programming and event list review, with temperature diagram Built-in battery keeps the device operative in case of power loss, for up to 12h DOOR MASTER Controlling of gate or garage door by smartphone, with real feedback about the position of the gate and no communication cost KEY FEATURES Starting the relay for the gate drive Gate position supervision from the motor's supply wires with direct connection Gate position monitoring from the limit switch Sending notifications about opening, closing and failure, for the authorized users simultaneously Supervision and control through web site or smartphone application The number of users is not limited Events stored with authenication of source (who opened the gate and when) xdoor 3 Control of 3 different electric gates by smartphone of settnig a temporary authorization code for access control keypad 3 relays for starting the gate control DP-GSM 2G/3G cellular intercom with gate control function and IoT based remote management Wireless intercom with 1 or 2 pushbuttons 3 limit sitch input for 2 phone numbers can be monitoring the closed position assigned to each pushbutton of the gate 1 WIEGAND 26 input for access control keypad of RFID card reader Sending notifications about opening, closing and failure, for the authorized users simultaneously Configuration and diagnostic via WEB browser trough Internet connection (eg.set permissions, delete users, events monitoring) The number of users is not limited Event log with latest 1000 action Gate control function by free call, 100 user phone numbers can be configured Gate control function by smartphone App Configuration and diagnostic through both USB connection and WEB browser Stainless casing, vandal proof design through GPRS connection
through WIFI connection No router setup fo device installation 2 WIFI connections fo primary and backup access points (IEEE 802.11 b/g/n) Dial capture interface for alarm reporting (Admeco Contact ID) 2 digital OC outputs for arm/disarm control SERIAL connection for local or remote programming AUDIO monitoring port for dial capture interface Wide power supply: 9-24V DC with max. 200mA peak current Operating temperature: 0 C to +50 C through GPRS connection GPRS mobile connection (850/900/1800/1900 MHz) No router setup for device installation TECHNICAL DETAILS 2 WIFI connections for primary and backup access points (IEEE 802.11 b/g/n) through WIFI and/or GPRS connection 2 WIFI connections for primary and backup access points (IEEE 802.11 b/g/n) 2G or 3G mobile connection (voice and data) 2 contact inputs (NO type) Limit switch input (NO type) GPRS mobile connection (850/900/1800/1900 MHz) Controllable relay (NO type) 2 controllable relay (NO Controllable relay (NO type) 3 Limit switch input (No type) Controllable voltage output: type) 12V / 2A PT100 temp. Sensor input Motor monitoring inputs 3 Controllable relay (NO type) Appearance: surface and (range: -50 C to +150 C) (M+/M- up to 48V DC) flush mount design Li-lon battery powered Several power supply: 9-24V WEIGAND 26 input Power supply: 9-16V DC operation AC or DC with max. 200mA peak current. Wide power supply: 9-24V DC with max. 800mA peak current Operating temperature: 0 C Several power supply: 9-24V AC or DC with max. 500mA peak current