Instruction Manual Instruktionshåndbog Instruktionshandbok Käyttöohje 053 053 Genesis 53 Hydroneumatic ower Tool Hydro neumatisk Trykluftsværktøj Hydropneumatiskt Vertyg Hydropneumaattinen Työkalu
Contents English Safety Rules 4 Specifications Specification for 053 Tool 5 Tool Dimensions 5 Intent of Use 6 utting into Service Air Supply Mechanical Cursors Cursor Loading and Reloading the Tool 0 Operating rocedure 0 Mandrel Follower Springs Identification and Orientation Maintenance Dismantling 0530000 45 General Assembly and arts List 0530000 6 riming Oil Details Hyspin VG 3 and AWS Oil Safety Data riming ump riming rocedure Fault Diagnosis Symptom, ossible Cause and Remedy 30 Dansk 33 Svenska 63 Suomi 3 Nose Assemblies Nose Jaws Selecting a Nose Jaw 3 Nose Jaw Selection Imperial 4 Nose Jaw Selection Metric 5 Mandrels and Mandrel Follower Springs 6 Chobert and Grovit Imperial 6 Chobert and Grovit Metric Briv Imperial Mandrel Head Types and Length Briv Metric Avlug, Avsert, Avtronic and Rivscrew Imperial and Metric 0 Servicing the Tool Daily Weekly MolyLithium Grease E 335 Safety Data Molykote 55m Grease Safety Data Molykote Grease Safety Data Service Kits 3 LIMITED WARRANTY Avdel makes the limited warranty that its products will be free of defects in workmanship and materials which occur under normal operating conditions. This Limited Warranty is contingent upon: () the product being installed, maintained and operated in accordance with product literature and instructions, and () confirmation by Avdel of such defect, upon inspection and testing. Avdel makes the foregoing limited warranty for a period of twelve () months following Avdel delivery of the product to the direct purchaser from Avdel. In the event of any breach of the foregoing warranty, the sole remedy shall be to return the defective Goods for replacement or refund for the purchase price at Avdel option. THE FOREGOING EXRESS LIMITED WARRANTY AND REMEDY ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES. ANY IMLIED WARRANTY AS TO QUALITY, FITNESS FOR UROSE, OR MERCHANTABILITY ARE HEREBY SECIFICALLY DISCLAIMED AND EXCLUDED BY AVDEL. Avdel UK Limited policy is one of continuous product development and improvement and we reserve the right to change the specification of any product without prior notice. 3
Safety Rules This instruction manual must be read with particular attention to the following safety rules, by any person installing, operating, or servicing this tool. Do not use outside the design intent. Do not use equipment with this tool/machine other than that recommended and supplied by Avdel UK Limited. 3 Any modification undertaken by the customer to the tool/machine, nose assemblies, accessories or any equipment supplied by Avdel UK Limited or their representatives, shall be the customer s entire responsibility. Avdel UK Limited will be pleased to advise upon any proposed modification. 4 The tool/machine must be maintained in a safe working condition at all times and examined at regular intervals for damage and function by trained competent personnel. Any dismantling procedure shall be undertaken only by personnel trained in Avdel UK Limited procedures. Do not dismantle this tool/machine without prior reference to the maintenance instructions. lease contact Avdel UK Limited with your training requirements. 5 The tool/machine shall at all times be operated in accordance with relevant Health and Safety legislation. In the U.K. the Health and Safety at Work etc. Act 4 applies. Any question regarding the correct operation of the tool/machine and operator safety should be directed to Avdel UK Limited. 6 The precautions to be observed when using this tool/machine must be explained by the customer to all operators. Always disconnect the air line from the tool/machine inlet before attempting to adjust, fit or remove a nose assembly. Do not operate a tool/machine that is directed towards any person(s) or the operator. Always adopt a firm footing or a stable position before operating the tool/machine. 0 Ensure that vent holes do not become blocked or covered. The operating pressure shall not exceed bar. Do not operate the tool if it is not fitted with a complete nose assembly or swivel head unless specifically instructed otherwise. 3 Care shall be taken to ensure that spent stems are not allowed to create a hazard. 4 If the tool is fitted with a stem collector, it must be emptied when half full. 5 If the tool is fitted with a stem deflector, it should be rotated until the aperture is facing away from the operator and other person(s) working in the vicinity. 6 When using the tool, the wearing of safety glasses is required both by the operator and others in the vicinity to protect against fastener ejection, should a fastener be placed in air. We recommend wearing gloves if there are sharp edges or corners on the application. Take care to avoid entanglement of loose clothes, ties, long hair, cleaning rags etc. in the moving parts of the tool which should be kept dry and clean for best possible grip. When carrying the tool from place to place keep hands away from the trigger/lever to avoid inadvertent start up. Excessive contact with hydraulic fluid oil should be avoided. To minimize the possibility of rashes, care should be taken to wash thoroughly. 0 C.O.S.H.H. data for all hydraulic oils and lubricants is avialable on request from your tool supplier. IMORTANT While a small amount of wear and marking will naturally occur through normal and correct use of mandrels, they must be regularly examined for excessive wear and marking, with particular attention to the head diameter, the tail jaw gripping area of the shank or heavy pitting of the shank and any mandrel distortion. Mandrels which fail during use could forcibly exit the tool. It is the customer's responsibility to ensure that mandrels are replaced before any excessive levels or wear and always before the maximum recommended number of placings. Contact your Avdel UK Limited representative who will let you know what that figure is by measuring the broach load of your application with a calibrated test tool. These tools can also be purchased under art Number 000000, supplied with all necessary information for testing in this manual. 4
Specifications English Specification for 053 Tool Air ressure Minimum Maximum 5 bar (000 lbf/in ) Free Air Volume Required @ 5. bar /5 lbf/in.6 litres (0.0 ft 3 ) Stroke Minimum.0 mm (.0 in) ull Force @ 5.5 bar /0 lbf/in 3. kn (5 lbf) Cycle time Approximately second Noise Level Less than 0 db(a) Weight Tool.3 kg (5.06 lb) Vibration Less than.5 m/s ( ft/s ) Tool Dimensions art Number 0530000 33 3.30 45.0 60.36 5 50.6 053 63 40 6.4 5.5 3.5 053 0 50 0 5
Intent of Use The pneumatic 053 tool is a handheld lightweight tool designed to place Avdel speed fasteners (except /6 Avlug ) making it ideal for batch or flowline assembly in a wide variety of applications throughout all industries. art numbers are shown to order a complete tool but no nose equipment. The tool part number for the 053 model is 0530000. See the general assemblies on pages 6. The tool will place most repetition fasteners, as shown in the table below. The tool is used with specific nose equipment. Reference must be made to the Nose Equipment section of the manual when selecting compatible components for the type and size of fastener used in your application (see pages 0). Nose jaw dimensions are shown on page 3. 6
4 0 6 utting into Service English Air Supply All tools are operated with compressed air at an optimum pressure of 5.5 bar. We recommend the use of pressure regulators and filtering systems on the main air supply. These should be fitted within 3 metres of the tool (see diagram below) to ensure maximum tool life and minimum tool maintenance. Air supply hoses should have a minimum working effective pressure rating of 50% of the maximum pressure produced in the system or 0 bar, whichever is the highest. Air hoses should be oil resistant, have an abrasion resistant exterior and should be armoured where operating conditions may result in hoses being damaged. All air hoses MUST have a minimum bore diameter of 6.4 millimetres or /4 inch. Read servicing daily details page. STO COCK (USED DURING MAINTENANCE OF FILTER/REGULATOR UNIT) TAKE OFF OINT FROM MAIN SULY 3 METRES MAXIMUM 053 046 MAIN SULY DRAIN OINT RESSURE REGULATOR AND FILTER (DRAIN DAILY)
utting into Service Mechanical Cursors 053 TOOL BARREL SRING LOADED END 053 CURSOR NOSE JAWS For reference there are three different mechanical cursor types: 0000 Used for Standard mandrels and 5/3 Disposable mandrels 00543 Used for / Disposable mandrels 00545 Used for 3/6 Disposable mandrels The difference in the above assemblies is the internal diameter of the End lug. END LUG These are colour coded see below: MECHANICAL CURSOR ART NO. END LUG ART NO. COLOUR HOLE DIAMETER (mm) 0000 0500040 LAIN STEEL. 00543 050544 GOLD. 00545 050546 SILVER 3.3
utting into Service English Cursor IMORTANT If fitted incorrectly, the cursor will not allow feeding of the fasteners. While the cursor will be fitted the correct way round when the tool is supplied, we recommend that you check its orientation before fitting the nose equipment. The sprung loaded, slightly concave, end of the cursor should point towards the front of the tool as shown in the illustration. When fitted the correct way round, the cursor will easily slide out of the barrel when a mandrel is pushed into its centre then pulled back. To reverse the orientation of the cursor, follow these steps: Item numbers in bold refer to the general assembly and parts list for the 0530000 on pages 6. Remove the Clip 4 and slide off End Cap 50. Using an Allen Key, remove one Cap Head Screw 5 ensuring that any trapped air is exhausted. remove the second Cap Head Screw 5. ull out Rear lug 4. ull out Tail Jaw iston Assembly 5 together with Jaws 34. Lift out Spring 35 and Jaw Housing 4. SRING LOADED END CURSOR NOSE JAWS TOOL BARREL Insert a mandrel into the hole in the rear end of Barrel 44 until it protrudes through the front of the barrel, then pull out the mandrel and cursor together through the front. Reassemble components in reverse order. Insert Mechanical Cursor Assembly 36 into the front of the barrel, correct way round. Loading and Reloading the Tool IMORTANT The procedure for loading the tool and for fitting the nose equipment to the tool is integral. When ordering a complete tool or system you will normally be supplied with all the nose equipment required for the fastener to be placed. To identify nose equipment components or to select the correct elements, read the nose equipment section, on pages 0. If you have been supplied with a nose jaw, mandrels and mandrel follower springs proceed with loading the tool and fitting the nose equipment as shown overleaf. Item numbers in bold refer to the general assembly and parts list for the 0530000 on pages 6.
utting into Service Loading the Tool Connect the air supply to the tool. Open Tail Jaws 34 which grip the mandrel, by switching off the tail jaw switch (items and 3). Screw selected nose jaws onto Barrel 44 of the tool. * Insert a mandrel into the tail end of the fasteners through the paper pod. Slide the mandrel follower spring onto the mandrel ensuring correct orientation, as shown in the table on page. Gripping the tail end of the mandrel, tear off the paper pod from around the fasteners. Open the nose jaws either by rotating the outer ring on Cam operated jaws or by pushing outwards on the jaw ends, as illustrated below left. Insert the previously assembled mandrel, mandrel follower spring and fasteners into the nose jaws until the first fastener to be placed is protruding from the nose jaw. Close the nose jaws and adjust so that the first fastener protrudes by.5mm 3mm ( /6 to / ), as shown in the illustration below right. Close the tail jaws to ensure the mandrel is gripped, by switching on the tail jaw switch (items and 3)..5mm 3mm ( /6" /") Reloading the Tool Open Tail Jaws 34 of tool. Open the nose jaws and pull the empty mandrel and mandrel follower spring out of the tool. Reload the tool by following the above instructions, starting at stage *. Operating rocedure IMORTANT You must check that the cursor orientation and the nose equipment are correct before attempting to operate the tool. ush the fastener, protruding from the nose jaws, fully into the application holes ensuring that the tool is held square. Operate the trigger without releasing the mandrel head is pulled through the fastener, forming the fastener into the application. Remove the tool. Release the trigger. The next fastener will be automatically presented through the nose jaws, ready for placing. Item numbers in bold refer to the general assembly and parts list for the 0530000 on pages 6. 0
utting into Service English MANDREL FOLLOWER SRINGS IDENTIFICATION AND ORIENTATION FASTENER NAME SIZE NOSE JAW (SEE NOSE EQUIMENT SECTION) MANDREL SIZE MANDREL/MANDREL FOLLOWER SRING AND FASTENER ASSEMBLY MANDREL FOLLOWER SRING 3 /3" STANDARD TAERED ALL MANDREL HEAD FERRULE SRING MANDREL BRIV 3 /3" LIMITED ACCESS & LIMITED ACCESS CAM OERATED ALL /" ALL ALL 5 /3" ALL ALL 3 /6" ALL ALL 6mm STANDARD ALL EXCET 3rd OVERSIZE CHOBERT AVLUG GROVIT 3 /3" 3 /3" ALL EXCET STANDARD TAERED, LIMITED ACCESS STANDARD TAERED, LIMITED ACCESS ALL ALL /" ALL ALL 5 /3" ALL ALL EXCET 3rd OVERSIZE CHOBERT GROVIT 5 /3" 3 /6" ALL ALL 3rd OVERSIZE ALL EXCET nd OVERSIZE 3 /6" ALL nd OVERSIZE CHOBERT /4" ALL ALL RIVSCREW.mm 3mm ALL ALL 3.5mm 4mm ALL ALL AVSERT.5mm 4 x 40 UNC ALL ALL 3mm 6 x 3 UNC ALL ALL.5mm ALL ALL AVTRONIC.mm ALL EXCET LIMITED ACCESS ALL.mm LIMITED ACCESS ALL
Nose Assemblies On speed fastening tools such as 053 MkII type, the nose equipment always consists of three elements: a nose jaw, a mandrel and a mandrel follower spring. All three items are matched to the fastener being placed and to the hole size in the application. IMORTANT To avoid complete dismantling of the tool it is essential to check the orientation of the cursor before fitting the nose equipment to the tool. See CURSOR section on page. It is essential that the correct nose equipment is fitted to the tool to ensure both effective placing of the fastener and SAFE operation of the tool. READ THE SAFETY INSTRUCTIONS page 4 carefully. To identify the correct combination of nose equipment to fit your tool first select a nose jaw by reading the section below then read the mandrel section to select part numbers both for the mandrel itself and for the mandrel follower spring. Mandrels and mandrel follower springs are illustrated on page. To fit the nose equipment, follow the Loading the Tool procedure page 0. Nose Jaws IMORTANT The wrong nose jaw could result in an incorrectly placed fastener or incorrect clench. Nose Jaws can be categorised into different basic shapes as illustrated opposite, even though internal dimensions will vary according to the fastener it is intended for. Exact dimensions referring to the letters in the illustrations opposite are indicated in the Nose Jaw Selection Tables on pages 45. For a particular shape, there may be several options of end form giving access benefits or fastener placing enhancement. Flat Normal end form of all nose jaws. Suitable on all applications with no access restrictions. Universal Designed for use with universal head Chobert fasteners. Can also be used with Briv fasteners to obtain the highest possible clench. Note this reduces the maximum grip range of the Briv fastener by approximately 0.05 (0.4mm). Recessed For use with Briv fasteners ONLY. It gives a higher clench than a flat end form but less than a universal end form, with no reduction of the grip range of the fastener. Tapered Available as shown in the Nose Jaw Selection Tables. Allows greater accessibility than a flat end form and places the same range. Head Forming For use with Rivscrew fasteners ONLY. Deforms the head of the fastener to achieve good clench.
Nose Assemblies English Selecting a Nose Jaw List the name, size and material of the fastener to be placed. Look for this fastener in the first column of the nose jaw selection tables on page 4 if you use imperial measurements and on page 5 if you use metric units. STANDARD Looking right across the table, take note of which nose jaws are available. ONLY those shown are available. Select which is most suitable for your application by referring to the respective nose jaw drawing. If your application has no access restriction, you should select the standard shape with a flat end form with or without a cam..6.5 33.5.3 'D' 'B' 'E' FLAT UNIVERSAL RECESSED TAERED Available in 4 different end forms to place all fasteners (except Rivscrew). Suitable on applications with no or little access restriction..6.5 LONG 'B' LONG CURVED 'B' LIMITED ACCESS 'B' 33.5.3 'D' 'E' 33.5.3.6.5 'D' 'F' 'E' 0.5 0. 4.4.63 'D' 'E' RIVET Ø 'F' mm in. /.60 5. 5/3.60.5 3/6.0.3 FLAT UNIVERSAL RECESSED FLAT RECESSED FLAT Available to place most of the fasteners. Allows more penetration into applications with no other access restriction. Available as shown in NOSE JAW SELEC TION TABLE. Allows more penetration into applications with restricted access. Mandrels must be curved by hand to follow the shape of the jaw. Available as shown in NOSE JAW SELEC TION TABLE. Allows access into very restrictive applications. STANDARD CAM OERATED 'B' LONG CAM OERATED 'B' LIMITED ACCESS CAM OERATED 'B'.6.5 34.34 'D' 'E'.6.5 34.34 'D' 'E'.6.5 3..46 'D' 'E' FLAT HEAD FORMING (HF) FLAT FLAT Available as shown in NOSE JAW SELECTION TABLE overleaf. Equivalent functions to the Standard and Limited Access above with the addition of a cam to ease and speed up the nose jaw opening thus the pod reloading procedure. Dimensions shown in bold are millimetres. Other dimensions are in inches. 3
Nose Assemblies Nose Jaw Selection Imperial The REF Nº column cross references with the REF Nº columns in the mandrel section. It identifies both the mandrel and mandrel follower spring required for a particular nose jaw with a specific fastener. FASTENER REF. Nº TYE AND END FORM STANDARD FLAT NOSE JAW ART Nº 05003003 DIMENSIONS 'B' 'D' 'E'.36.30.6 REF. Nº NOSE JAW TYE AND END FORM ART Nº # STANDARD UNIVERSAL 0500303 DIMENSIONS 'B' 'D' 'E'.36.33.4 3/3" CHOBERT STD. CAM OERATED FLAT STANDARD TAERED 0004500 000303.36.36.30.30.6.6 3 LTD. ACCESS CAM OERATED LIMITED ACCESS 003003 040000.0...0.6.6 4 LONG FLAT 05004003.4.30.6 4 LONG CURVED FLAT 05005003.4..6 5 STANDARD FLAT 05003004.4..0 5 # STANDARD UNIVERSAL 0500304.4..3 /" CHOBERT 5 6 STANDARD TAERED LONG FLAT 000304 05004004.4.4...0.0 5 6 STD. CAM OERATED FLAT # LONG UNIVERSAL 0004600 0500404.4.4...0.30 6 LONG CURVED FLAT 05005004.4..0 6 LONG CAM OERATED FLAT 0005000.4..0 STANDARD FLAT 05003005.4.30.4 # STANDARD UNIVERSAL 0500305.4.35.4 5/3" CHOBERT STANDARD TAERED LONG FLAT 0500305 05004005.44.4.30.30.4.4 STD. CAM OERATED FLAT # LONG UNIVERSAL 000400 0500405.4.4.30.35.4.4 LONG CURVED FLAT 05005005.4.3.4 LONG CAM OERATED FLAT 000500.4.30.4 STANDARD FLAT 05003006.56..33 # STANDARD UNIVERSAL 0500306.56.4.4 3/6" CHOBERT 0 STANDARD TAERED LONG FLAT 0500306 05004006.56.56..30.33.33 0 STD. CAM OERATED FLAT # LONG UNIVERSAL 000400 0500406.56.56..3.33.4 0 LONG CURVED FLAT 05005006.56..33 0 LONG CAM OERATED FLAT 000500.56.30.33 /4" CHOBERT STANDARD FLAT LONG FLAT 0500300 0500400.64.64...3.3 STD. CAM OERATED FLAT LONG CAM OERATED FLAT 000400 0005300.64.64...3.3 3/3" BRIV Brass only 3 4 STANDARD TAERED LIMITED ACCESS 000303 040000.36..30.0.5.6 4 LTD. ACCESS CAM OERATED 003003.0..6 /" BRIV Al. Alloy, Brass, Steel 5 5 6 6 STANDARD FLAT STANDARD TAERED LONG RECESSED LONG CURVED RECESSED 05003004 000304 000304 0003304.4.4.4.4.....0.0.30.30 5 6 6 STANDARD RECESSED LONG FLAT LONG CURVED FLAT 0003004 05004004 05005004.4.4.4.0...30.0.0 5/3" BRIV Al. Alloy, Brass, Steel STANDARD FLAT LONG FLAT LONG CURVED FLAT 05003005 05004005 05005005.4.4.4.30.30.3.4.4.4 STANDARD RECESSED LONG RECESSED LONG CURVED RECESSED 0003005 000305 0003305.4.4.4.3.30.3.4.4.4 5/3" BRIV St.Steel only 0 0 STANDARD FLAT LONG FLAT LONG CURVED FLAT 05003005 05004005 05005005.4.4.4.30.30.3.4.4.4 0 0 STANDARD RECESSED LONG RECESSED LONG CURVED RECESSED 0003005 000305 0003305.4.4.4.3.30.3.4.4.4 3/6" BRIV Al. Alloy, Brass, Steel STANDARD FLAT LONG FLAT LONG CURVED FLAT 05003006 05004006 05005006.56.56.56..30..33.33.33 STANDARD RECESSED LONG RECESSED LONG CURVED RECESSED 0003006 000306 0003306.56.56.56.0.30..4.4.4 3/6" BRIV St.Steel only 3 4 4 STANDARD FLAT LONG FLAT LONG CURVED FLAT 05003006 05004006 05005006.56.56.56..30..33.33.33 3 4 4 STANDARD RECESSED LONG RECESSED LONG CURVED RECESSED 0003006 000306 0003306.56.56.56.0.30..4.4.4 6mm BRIV Al. Alloy, Steel 3/3" AVLUG /" AVLUG.5mm, 440 UNC AVSERT 3.0mm, 63 UNC AVSERT.5mm AVTRONIC.mm AVTRONIC.mm RIVSCREW 3.0mm RIVSCREW 3.5mm RIVSCREW 4.0mm RIVSCREW 5 6 30 3 3 33 34 35 3 3 3 40 4 STD. CAM OERATED LONG CAM OERATED STANDARD FLAT STD. CAM OERATED FLAT LONG CURVED FLAT STANDARD FLAT STD. CAM OERATED FLAT LONG CURVED FLAT STANDARD FLAT STANDARD FLAT STANDARD FLAT LONG FLAT STANDARD FLAT LONG FLAT STD. CAM OERATED HF STD. CAM OERATED HF STD. CAM OERATED HF STD. CAM OERATED HF 0005600 000500 05003003 0004500 05005003 05003004 0004600 05005004 05003003 05003004 05003003 05004003 005600 00500 003000 003000 003500 004000.64.64.36.36.4.4.4.4.36.4.36.4.36.4.4.4.4.4...30.30.....30..30.30.30.30.....5.5.6.6.6.0.0.0.6.0.6.6.6.6.4.4.4.5 5 6 30 30 3 33 36 STANDARD FLAT LONG FLAT STANDARD TAERED LONG FLAT STANDARD TAERED LONG FLAT LONG CAM OERATED FLAT STD. CAM OERATED FLAT LTD. ACCESS CAM OERATED LTD. ACCESS CAM OERATED 000500 000500 0500303 05004003 000304 05004004 0005000 0004600 00000 0000.64.64.36.4.4.4.4.4.4.40...30.30.......5.5.6.6.0.0.0.0.6.6 # These nose jaws are suitable for placing Chobert rivets with a Universal Head Form. When used on the equivalent size of Briv, the highest possible clench is achieved. Note when using Briv fasteners, the maximum grip is reduced by approximately 0.05" (0.4mm). 4
Nose Assemblies English Nose Jaw Selection Metric FASTENER REF. Nº TYE AND END FORM STANDARD FLAT NOSE JAW ART Nº 05003003 DIMENSIONS 'B' 'D' 'E'.4 33.0 4.06 REF. Nº NOSE JAW TYE AND END FORM ART Nº # STANDARD UNIVERSAL 0500303 DIMENSIONS 'B' 'D' 'E'.4 33. 6.0 3/3" CHOBERT STD. CAM OERATED FLAT STANDARD TAERED 0004500 000303.4.4 33.0 4.06 33.0 4.06 3 LTD. ACCESS CAM OERATED LIMITED ACCESS 003003 040000 5.0 5.5. 4.06. 4.06 4 LONG FLAT 05004003 0.4 5.4 4.06 4 LONG CURVED FLAT 05005003 0.4 5. 4.06 5 STANDARD FLAT 05003004 0.4. 5.0 5 # STANDARD UNIVERSAL 0500304 0.4 30..3 /" CHOBERT 5 6 STANDARD TAERED LONG FLAT 000304 05004004 0.4 30.3 5.0 0.4 55.3 5.0 5 6 STD. CAM OERATED FLAT # LONG UNIVERSAL 0004600 0500404 0.4. 5.0 0.4 56.3.6 6 LONG CURVED FLAT 05005004 0.4 53.5 5.0 6 LONG CAM OERATED FLAT 0005000 0.4 55.3 5.0 STANDARD FLAT 05003005. 33.0 6.0 # STANDARD UNIVERSAL 0500305. 34. 0.4 5/3" CHOBERT STANDARD TAERED LONG FLAT 0500305 05004005. 33.0 6.0. 5.4 6.0 STD. CAM OERATED FLAT # LONG UNIVERSAL 000400 0500405. 33.0 6.0. 5.6 0.6 LONG CURVED FLAT 05005005. 56.64 6.0 LONG CAM OERATED FLAT 000500. 5.4 6.0 STANDARD FLAT 05003006 4...3 # STANDARD UNIVERSAL 0500306 4. 3.50.4 3/6" CHOBERT 0 STANDARD TAERED LONG FLAT 0500306 05004006 4...3 4. 5.4.3 0 STD. CAM OERATED FLAT # LONG UNIVERSAL 000400 0500406 4...3 4. 60.. 0 LONG CURVED FLAT 05005006 4. 56.3.3 0 LONG CAM OERATED FLAT 000500 4. 5.4.3 /4" CHOBERT STANDARD FLAT LONG FLAT 0500300 0500400 6.6.. 6.6 55.3. STD. CAM OERATED FLAT LONG CAM OERATED FLAT 000400 0005300 6.6.. 6.6 55.3. 3/3" BRIV Brass only 3 4 STANDARD TAERED LIMITED ACCESS 000303 040000.4 5.5 33.0 3.. 4.06 4 LTD. ACCESS CAM OERATED 003003 5.0. 4.06 /" BRIV Al. Alloy, Brass, Steel 5 5 6 6 STANDARD FLAT STANDARD TAERED LONG RECESSED LONG CURVED RECESSED 05003004 000304 000304 0003304 0.4. 5.0 0.4 30.3 5.0 0.4 55.3.6 0.4 53.5.6 5 6 6 STANDARD RECESSED LONG FLAT LONG CURVED FLAT 0003004 05004004 05005004 0.4 30.4.6 0.4 55.3 5.0 0.4 53.5 5.0 5/3" BRIV Al. Alloy, Brass, Steel STANDARD FLAT LONG FLAT LONG CURVED FLAT 05003005 05004005 05005005. 33.0 6.0. 5.4 6.0. 56.64 6.0 STANDARD RECESSED LONG RECESSED LONG CURVED RECESSED 0003005 000305 0003305. 33.53 0.4. 5.4 0.4. 56.64 0.4 5/3" BRIV St.Steel only 0 0 STANDARD FLAT LONG FLAT LONG CURVED FLAT 05003005 05004005 05005005. 33.0 6.0. 5.4 6.0. 56.64 6.0 0 0 STANDARD RECESSED LONG RECESSED LONG CURVED RECESSED 0003005 000305 0003305. 33.53 0.4. 5.4 0.4. 56.64 0.4 3/6" BRIV Al. Alloy, Brass, Steel STANDARD FLAT LONG FLAT LONG CURVED FLAT 05003006 05004006 05005006 4...3 4. 5.4.3 4. 56.3.3 STANDARD RECESSED LONG RECESSED LONG CURVED RECESSED 0003006 000306 0003306 4. 30.4.4 4. 5.4.4 4. 56.3.4 3/6" BRIV St.Steel only 3 4 4 STANDARD FLAT LONG FLAT LONG CURVED FLAT 05003006 05004006 05005006 4...3 4. 5.4.3 4. 56.3.3 3 4 4 STANDARD RECESSED LONG RECESSED LONG CURVED RECESSED 0003006 000306 0003306 4. 30.4.4 4. 5.4.4 4. 56.3.4 6mm BRIV Al. Alloy, Steel 3/3" AVLUG /" AVLUG.5mm, 440 UNC AVSERT 3.0mm, 63 UNC AVSERT.5mm AVTRONIC.mm AVTRONIC.mm RIVSCREW 3.0mm RIVSCREW 3.5mm RIVSCREW 4.0mm RIVSCREW 5 6 30 3 3 33 34 35 3 3 3 40 4 STD. CAM OERATED LONG CAM OERATED STANDARD FLAT STD. CAM OERATED FLAT LONG CURVED FLAT STANDARD FLAT STD. CAM OERATED FLAT LONG CURVED FLAT STANDARD FLAT STANDARD FLAT STANDARD FLAT LONG FLAT STANDARD FLAT LONG FLAT STD. CAM OERATED HF STD. CAM OERATED HF STD. CAM OERATED HF STD. CAM OERATED HF 0005600 000500 05003003 0004500 05005003 05003004 0004600 05005004 05003003 05003004 05003003 05004003 005600 00500 003000 003000 003500 004000 6.33 30.65 3.4 6.33 55.65 3.4.4 33.0 4.06.4 33.0 4.06 0.4 5. 4.06 0.4. 5.0 0.4. 5.0 0.4 53.5 5.0.4 33.0 4.06 0.4. 5.0.4 33.0 4.06 0.4 5.4 4.06.4 33.0 4.06 0.4 5.4 4.06 0.4. 6.0 0.4. 6.0 0.4. 6.0 0.4. 6.35 5 6 30 30 3 33 36 STANDARD FLAT LONG FLAT STANDARD TAERED LONG FLAT STANDARD TAERED LONG FLAT LONG CAM OERATED FLAT STD. CAM OERATED FLAT LTD. ACCESS CAM OERATED LTD. ACCESS CAM OERATED 000500 000500 0500303 05004003 000304 05004004 0005000 0004600 00000 0000 6.33 30.65 3.4 6.33 55.65 3.4.4 33.0 4.06 0.4 5.4 4.06 0.4 30.3 5.0 0.4 55.3 5.0 0.4 55.3 5.0 0.4. 5.0 0.4. 4.06 0.6. 4.06 # These nose jaws are suitable for placing Chobert rivets with a Universal Head Form. When used on the equivalent size of Briv, the highest possible clench is achieved. Note that when using Briv fasteners, the maximum grip is reduced by approximately 0.05" (0.4mm). 5
Nose Assemblies Mandrels and Mandrel Follower Springs Mandrels and mandrel follower springs, illustrated on page need to be selected to suit the fastener type and size as well as the size of the hole in the application. Use of the wrong mandrel could increase the risk of breakage and the wear of the mandrel head. Feeding problems could occur if the wrong mandrel follower spring is used. IMORTANT READ THE SAFETY INSTRUCTIONS page 4 carefully. While a small amount of wear and marking will naturally occur through normal and correct use of mandrels, they must be regularly examined for excessive wear and marking, with particular attention to the head diameter, the tail jaw gripping area of the shank or heavy pitting of the shank and any mandrel distortion. Mandrels which fail during use could forcibly exit the tool. It is the customer s responsibility to ensure that mandrels are replaced before any excessive levels of wear and always before the maximum recommended number of placings. Contact your Avdel UK Limited representative who will let you know what that figure is by measuring the broach load of your application with our calibrated measuring tool. These tools can also be purchased under part number 000 000, supplied with all necessary information for testing. Chobert and Grovit Imperial For mandrel or mandrel follower spring selection, follow instructions on page. FASTENER REF. HOLE STANDARD MANDREL GREEN Nº SIZE HEAD Ø MANDREL ART Nº MAX..05 05006003.66 # S/R MANDREL ART Nº 0500003 MAX..0 HOLE SIZE +.005 HEAD Ø.04 ST OVERSIZE MANDREL YELLOW MANDREL ART Nº 05006303 MAX..4 # S/R MANDREL ART Nº MAX. SRING ART Nº 0500603 +.0035.06 050003.0 0500603 3/3" CHOBERT 3.05.05 05006003 05006003.66.66 0500003 0500003.0.0 +.005 +.0035 +.005.04.06.04 05006303 05006303.4.4 050003.0 00063 00063 000603 3 +.0035.06 050003.0 000603 4.05 0500003.66 0500003.0 +.0035.06 050003.0 050003 /" CHOBERT 5 6.0.0 05006004 0500004.6.6 0500004 0500004.00.00 +.004 +.004.0.0 0500604 050004.3.3 050004 050004.0.0 0500604 050004.0 05006005.44 0500005.00 +.00.5 0500605.4 050005.6 00065 5/3" CHOBERT.0 0500005.44 0500005.00 +.00.5 050005.4 050005.6 0005.3 05006006.4 0500006.0 +.04.46 0500606.30 050006.30 00066 3/6" CHOBERT 0.3 0500006.4 0500006.0 +.04.46 050006.30 050006.30 0006 0 /4" CHOBERT.4.4 0500600 050000.6.6 050000 050000.0.0 +.0 +.0.6.6 050060 05000.330.330 05000 05000.34.34 050060 05000 FASTENER ND OVERSIZE MANDREL BLUE REF. HOLE Nº SIZE HEAD MANDREL # S/R MANDREL Ø ART Nº MAX. ART Nº +.0035.06 0500603.5 MAX. HOLE SIZE HEAD Ø 3RD OVERSIZE MANDREL RED MANDREL ART Nº MAX. # S/R MANDREL ART Nº MAX. SRING ART Nº 0500603 3/3" CHOBERT 3 +.0035 +.0035.06.06 0500603 0500603.5.5 00063 000603 3 4 +.0035.06 050003.5 050003 /" CHOBERT 5 6 +.00 +.00.0.0 0500604 050004.6.6 050004 050004.0.0 +.04 +.04.0.0 05006304 0500304.. 0500304 0500304.. 0500604 050004 +.05. 0500605.30 050005.30 00065 5/3" CHOBERT +.05. 050005.30 050005.30 +.05.3 05006305.3 0500305.50 0500605 0005 +.05.3 0500305.3 0500305.50 050005 3/6" CHOBERT 0 +.04.56 0500606.3 050006.50 0500606 0 +.04.56 050006.3 050006.50 050006 /4" CHOBERT # S/R: Short Reach Mandrel. See page for explanation. 6
Nose Assemblies English Tables below left and right and over the next four pages list part numbers of all mandrels and mandrel follower springs available per fastener or group of fasteners, i.e. for Chobert and Grovit on these pages. While fastener sizes are always shown in their specified units, each table has been produced twice to offer dimensions in imperial units on the lefthand page then in metric units on the righthand page. These 'Mandrel Selection' tables crossreference with the 'Nose Jaw Selection' tables on pages 45 through the Ref. Nº column. It is the diameter of the head at the end of a mandrel which when pulled through controls the expansion of the fastener body. While there are different head shapes to suit different types of fasteners (see illustration on page ), progressive head sizes are needed to reflect manufacturing tolerances on the diameter of the hole in your application so that the fastener always expands sufficiently to fill the hole. Too large a mandrel head would overstress the mandrel and mandrels which fail during use could forcibly exit the tool. Selection tables are arranged into four 'mandrel size' sections, ranging from 'standard to '3rd oversize', each being colour coded as per the end of the mandrel heads themselves. Chobert and Grovit Metric FASTENER REF. Nº HOLE SIZE HEAD Ø.4 STANDARD MANDREL GREEN MANDREL ART Nº 05006003 MAX. 4. # S/R MANDREL ART Nº 0500003 MAX..0 HOLE SIZE +.04 HEAD Ø. ST OVERSIZE MANDREL YELLOW MANDREL ART Nº 05006303 MAX. 4.4 # S/R MANDREL ART Nº MAX. SRING ART Nº 0500603 +.0.3 050003. 0500603 3/3" CHOBERT.4 05006003 4. 0500003.0 +.04 +.0..3 05006303 4.4 050003. 00063 00063 3.4 05006003 4. 0500003.0 +.04. 05006303 4.4 000603 3 +.0.3 050003. 000603 4.4 0500003 4. 0500003.0 +.0.3 050003. 050003 /" CHOBERT 5 6.4.4 05006004 0500004 5.4 5.4 0500004 0500004.. +.0 +.0.34.34 0500604 050004 6.0 6.0 050004 050004.4.4 0500604 050004. 05006005 6.0 0500005.54 +.0. 0500605. 050005.5 00065 5/3" CHOBERT. 0500005 6.0 0500005.54 +.0. 050005. 050005.5 0005 3.35 05006006 6. 0500006.5 +.35 3. 0500606.3 050006 3.30 00066 3/6" CHOBERT 0 3.35 0500006 6. 0500006.5 +.35 3. 050006.3 050006 3.30 0006 0 /4" CHOBERT 4.6 4.6 0500600 050000 6. 6. 050000 050000.. +.30 +.30 4. 4. 050060 05000.3.3 05000 05000 3.40 3.40 050060 05000 FASTENER REF. Nº HOLE SIZE +.0 HEAD Ø.3 ND OVERSIZE MANDREL BLUE MANDREL ART Nº 0500603 MAX. 4.0 # S/R MANDREL ART Nº MAX. HOLE SIZE HEAD Ø 3RD OVERSIZE MANDREL RED MANDREL ART Nº MAX. # S/R MANDREL ART Nº MAX. SRING ART Nº 0500603 3/3" CHOBERT 3 +.0 +.0.3.3 0500603 0500603 4.0 4.0 00063 000603 3 4 +.0.3 050003 4.0 050003 /" CHOBERT 5 6 +.5 +.5.4.4 0500604 050004 6. 6. 050004 050004.. +.35 +.35.5.5 05006304 0500304.3.3 0500304 0500304 3.00 3.00 0500604 050004 +.3 3.0 0500605.3 050005 3.30 00065 5/3" CHOBERT +.3 3.0 050005.3 050005 3.30 +.63 3.35 05006305.45 0500305 3. 0500605 0005 +.63 3.35 0500305.45 0500305 3. 050005 3/6" CHOBERT 0 +.60 3.6 0500606.45 050006 3. 0500606 0 +.60 3.6 050006.45 050006 3. 050006 /4" CHOBERT # S/R: Short Reach Mandrel. See page for explanation.
Nose Assemblies To find the correct part number of a mandrel for a particular application, read the instructions below after you have gathered the following information as per example alongside. Answers for the example are shown in grey italic. FASTENER NAME example Chobert FASTENER SIZE / DATASHEET Series 5 ALICATION HOLE SIZE 0.335 CLEARANCE BEHIND ALICATION Infinite REF.Nº FROM NOSE JAW SELECTION TABLE 5 (standard flat) Subtract the minimum hole size recommended () in the fastener datasheet from the actual application hole size. example: 0.005. Turn to the page with the Mandrel Selection table for your fastener, selecting either the imperial or the metric dimensions table (pages 60). example: page 6. Staring with the Standard Mandrel Green section, find your fastener size in the lefthand column. example / Chobert & Grovit. If you selected a nose jaw which place you fastener, you should now be able to find a line within your fastener section with the same Ref No. as that from the Nose Jaw Selection table. example: 5. This is your line Ref. No. in which you will find both your mandrel and mandrel follower spring part number. This line continues into the second half of the table for the nd and 3rd oversize mandrels. Scan along the line to the hole size columns and select which ever is the nearest or equal to the figure calculated in step one. You may now read the mandrel part number next to the hole size. example: 0500604 For Chobert and Grovit only, most mandrels are also available in a short reach version (see illustration on page ). Short reach mandrels are used to minimise the possibility of the mandrel head contacting an obstruction. This would result in the underside of the fastener head not seating properly on the application surface, causing a lack on clench in the joint. Whichever size mandrel you settle on, you will also need to check the figure against that mandrel is adequate. is the clearance required for the mandrel head at the back of the application IN ADDITION to the length of the fastener protruding through the application, as shown in the illustration on page. You may now read the corresponding mandrel follower spring part number in the righthand column of the table. example: 050 0604. In all cases, satisfactory clenching of the joint should be assessed particularly if the size of the hole in your application is very close to the next oversize hole condition, when it will be safe to select the greater size of mandrel to obtain a higher clench. REMEMBER that this will increase the broach load and reduce the mandrel life. Briv Imperial For mandrel or mandrel follower spring selection, follow instructions above. FASTENER 3/3" BRIV Brass only /" BRIV Al. Alloy, Brass, Steel 5/3" BRIV Al. Alloy, Brass, Steel 5/3" BRIV St.Steel only 3/6" BRIV Al. Alloy, Brass, Steel 3/6" BRIV St.Steel only 6mm BRIV Al. Alloy, Steel REF. Nº 3 4 5 6 0 3 4 5 6 HOLE SIZE AS REC AS REC HEAD Ø.0.0.0.0.0.0.0.0.4.4.53.53.. STANDARD MANDREL GREEN MANDREL ART Nº 0500603 0500603 00644 0044 0500605 050005 000605 00005 0500606 050006 000606 00006 050060 05000 MAX....0.0.36.36.6.6.5.5.50.50.65.65 HOLE SIZE +.004 +.004 +.005 +.005 +.005 +.005 +.005 +.005 +.005 +.005 +.005 +.005 +.005 +.005 HEAD Ø.06.06.0.0.5.5.5.5.46.46.5.5.4.4 ST OVERSIZE MANDREL YELLOW MANDREL ART Nº 050063 050063 00654 0054 050065 05005 00065 0005 050066 05006 00066 0006 05006 0500 MAX..3.3.6.6.4.4.3.3.64.64.56.56.. SRING ART Nº 00063 000603 050064 05004 00065 0005 00065 0005 00066 0006 00066 0006 0500646 050046 FASTENER 3/3" BRIV Brass only REF. Nº 3 4 HOLE SIZE +.00 +.00 HEAD Ø.0.0 ND OVERSIZE MANDREL BLUE MANDREL ART Nº 050063 050063 MAX..6.6 HOLE SIZE HEAD Ø 3RD OVERSIZE MANDREL RED MANDREL ART Nº MAX. SRING ART Nº 00063 000603 /" BRIV Al. Alloy, Brass, Steel 5 6 +.00 +.00.0.0 00664 0064.33.33 050064 05004 5/3" BRIV Al. Alloy, Brass, Steel +.00 +.00.0.0 050065 05005.4.4 00065 0005 5/3" BRIV St.Steel only 0 3/6" BRIV Al. Alloy, Brass, Steel +.00 +.00.5.5 050066 05006.0.0 +.0 +.0.53.53 0500636 050036.3.3 00066 0006 3/6" BRIV St.Steel only 3 4 6mm BRIV Al. Alloy, Steel 5 6 +.00 +.00.. 05006 0500.. 0500646 050046
Nose Assemblies English Mandrel Head Types and Length Mandrels for stainless steel Briv are easily identifiable by a V cut in the end of the mandrel heads. When using curved nose jaws, mandrels have to be bent by hand to match the curvature of the nose jaw, thus ensuring good feed of fasteners. CHOBERT, GROVIT, AVSERT, AVTRONIC SHORT REACH (CHOBERT & GROVIT ONLY) BRIV BRIV (STAINLESS STEEL) RIVSCREW AVLUG Briv Metric FASTENER 3/3" BRIV Brass only REF. Nº 3 4 HOLE SIZE HEAD Ø.3.3 STANDARD MANDREL GREEN MANDREL ART Nº 0500603 0500603 MAX. 3.0 3.0 HOLE SIZE +.0 +.0 HEAD Ø.3.3 ST OVERSIZE MANDREL YELLOW MANDREL ART Nº 050063 050063 MAX. 3. 3. SRING ART Nº 00063 000603 /" BRIV Al. Alloy, Brass, Steel 5 6.34.34 00644 0044 3.05 3.05 +.3 +.3.46.46 00654 0054 3.0 3.0 050064 05004 5/3" BRIV Al. Alloy, Brass, Steel.. 0500605 050005 3.45 3.45 +.3 +.3.. 050065 05005 3.6 3.6 00065 0005 5/3" BRIV St.Steel only 0 3.05 3.05 000605 00005 3.0 3.0 +.3 +.3 3. 3. 00065 0005 3.35 3.35 00065 0005 3/6" BRIV Al. Alloy, Brass, Steel 3.5 3.5 0500606 050006 3. 3. +.3 +.3 3. 3. 050066 05006 4. 4. 00066 0006 3/6" BRIV St.Steel only 3 4 3. 3. 000606 00006 3. 3. +.3 +.3 4.0 4.0 00066 0006 3.6 3.6 00066 0006 6mm BRIV 5 AS REC 4.54 050060 4. +.3 4.6 05006 4.34 0500646 Al. Alloy, Steel 6 AS REC 4.54 05000 4. +.3 4.6 0500 4.34 050046 FASTENER 3/3" BRIV Brass only REF. Nº 3 4 HOLE SIZE +.0 +.0 HEAD Ø.0.0 ND OVERSIZE MANDREL BLUE MANDREL ART Nº 050063 050063 MAX. 3.0 3.0 HOLE SIZE HEAD Ø 3RD OVERSIZE MANDREL RED MANDREL ART Nº MAX. SRING ART Nº 00063 000603 /" BRIV Al. Alloy, Brass, Steel 5 6 +.5 +.5.5.5 00664 0064 3.3 3.3 050064 05004 5/3" BRIV Al. Alloy, Brass, Steel +.5 +.5 3.05 3.05 050065 05005 3. 3. 00065 0005 5/3" BRIV St.Steel only 0 3/6" BRIV Al. Alloy, Brass, Steel +.5 +.5 3.4 3.4 050066 05006 4.3 4.3 +.30 +.30 3.5 3.5 0500636 050036 4.3 4.3 00066 0006 3/6" BRIV St.Steel only 3 4 6mm BRIV Al. Alloy, Steel 5 6 +.5 +.5 4. 4. 05006 0500 4.4 4.4 0500646 050046
Nose Assemblies Avlug, Avsert, Avtronic and Rivscrew Imperial and Metric For mandrel or mandrel follower spring selection, follow instructions on page. FASTENER 3/3" AVLUG REF. Nº HOLE SIZE HEAD Ø.06.06 STANDARD MANDREL GREEN MANDREL ART Nº 05006603 0500603 MAX..353.353 HOLE SIZE +.005 +.003 HEAD Ø.0.0 ST OVERSIZE MANDREL YELLOW MANDREL ART Nº 0500603 050003 MAX..4.36 SRING ART Nº 0500603 050003 /" AVLUG 30.0.0 05006604 0500604.53.53 0500604 050004.5mm, 440 UNC AVSERT 3.05 05006003.45 0500603 3.0mm, 63 UNC AVSERT 3.0 05006004.5 0500604.5mm AVTRONIC 33 34.00.00 000605 00005.40.40 +.003 +.003.03.03 00065 0005.40.40 0500603 050003 35.0 00060.50 +.003.0 0006.50 00065.mm AVTRONIC 36.0 00060.50 +.003.0 0006.50 00063 3.0 0000.50 +.003.0 000.50 0005.mm RIVSCREW 3 *.065 006030. 006630 3.0mm RIVSCREW 3 *.065 006030. 006630 3.5mm RIVSCREW 40 *.05 006035.3 006635 4.0mm RIVSCREW 4 *.03 00640.50 006640 * These Dimensions are Across Flats FASTENER 3/3" AVLUG REF. Nº HOLE SIZE HEAD Ø ND OVERSIZE MANDREL BLUE MANDREL ART Nº MAX. HOLE SIZE HEAD Ø 3RD OVERSIZE MANDREL RED MANDREL ART Nº MAX. SRING ART Nº /" AVLUG 30.5mm, 440 UNC AVSERT 3 3.0mm, 63 UNC AVSERT 3.5mm AVTRONIC 33 34 +.006 +.006.06.06 00065 0005.40.40 0500603 050003 35 +.006.05 0006.50 00065.mm AVTRONIC 36 +.006.05 0006.50 00063 3 +.006.05 000.50 0005.mm RIVSCREW 3 3.0mm RIVSCREW 3 3.5mm RIVSCREW 40 4.0mm RIVSCREW 4 FASTENER 3/3" AVLUG LINE Nº HOLE SIZE HEAD Ø.3.3 STANDARD MANDREL GREEN MANDREL ART Nº 05006603 0500603 MAX... HOLE SIZE +.0 +.0 HEAD Ø.06.0 ST OVERSIZE MANDREL YELLOW MANDREL ART Nº 0500603 050003 MAX..4.35 SRING ART Nº 0500603 050003 /" AVLUG 30.4.4 05006604 0500604 5.06 5.06 0500604 050004.5mm, 440 UNC AVSERT 3.4 05006003 3.6 0500603 3.0mm, 63 UNC AVSERT 3.4 05006004 4.0 0500604.5mm AVTRONIC 33 34.. 000605 00005 3.56 3.56 +.0 +.0.5.5 00065 0005 3.56 3.56 0500603 050003 35.0 00060 3. +.0.0 0006 3. 00065.mm AVTRONIC 36.0 00060 3. +.0.0 0006 3. 00063 3.0 0000 3. +.0.0 000 3. 0005.mm RIVSCREW 3 AS REC *.65 006030 3.3 006630 3.0mm RIVSCREW 3 *.65 006030 3.3 006630 3.5mm RIVSCREW 40 *.0 006035 3.35 006635 4.0mm RIVSCREW 4 *.6 00640 3. 006640 * These Dimensions are Across Flats FASTENER 3/3" AVLUG LINE Nº HOLE SIZE HEAD Ø ND OVERSIZE MANDREL BLUE MANDREL ART Nº MAX. HOLE SIZE HEAD Ø 3RD OVERSIZE MANDREL RED MANDREL ART Nº MAX. SRING ART Nº /" AVLUG 30.5mm, 440 UNC AVSERT 3 3.0mm, 63 UNC AVSERT 3.5mm AVTRONIC 33 34 +.5 +.5.3.3 00065 0005 3.56 3.56 0500603 050003 35 +.5.6 0006 3. 00065.mm AVTRONIC 36 +.5.6 0006 3. 00063 3 +.5.6 000 3. 0005.mm RIVSCREW 3 3.0mm RIVSCREW 3 3.5mm RIVSCREW 40 4.0mm RIVSCREW 4 0
Servicing the Tool English Regular servicing should be carried out and a comprehensive inspection performed annually or every 500,000 cycles, whichever is sooner. IMORTANT The employer is responsible for ensuring that tool maintenance instructions are given to the appropriate personnel. The operator should not be involved in maintenance or repair of the tool unless properly trained. Daily Daily, before use or when first putting the tool into service. our a few drops of clean lubricating oil into the air inlet of the tool if no lubricator is fitted on air supply. If the tool is in continuous use, the air hose should be disconnected from the main air supply and the tool lubricated every two to three hours. Check for air and oil leaks. If damaged, hoses and couplings should be replaced. If there is no filter on the pressure regulator, bleed the airline to clear it of accumulated dirt or water before connecting the air hose to the intensifier. If there is a filter, drain it. Check that the nose equipment is correct. Check mandrels regularly for signs of wear or damage monitoring the number of placings (read the safety instructions on page 4). Check the base cover is fully tightened onto the body. Weekly Conduct the full Daily procedures as described above. Remove, inspect, clean and grease the Tail Jaws (refer to Tail Jaw Cylinder in the "Maintenance Section" page 4). MolyLithium Grease E 353 Safety Data Grease can be ordered as a single item, the part number is shown in the Service Kits page 3. First Aid SKIN: As the grease is completely water resistant it is best removed with an approved emulsifying skin cleaner. INGESTION: Ensure the individual drinks 30ml Milk of Magnesia, preferably in a cup of milk. EYES: Irritant but not harmful. Irrigate with water and seek medical attention. Fire FLASH OINT: Above 0 C. Not classified as flammable. Suitable extinguishing media: CO, Halon or water spray if applied by an experienced operator. Environment Scrape up for burning or disposal on approved site. Handling Use barrier cream or oil resistant gloves Storage Away from heat and oxidising agent.
Servicing the Tool Molykote 55m Grease Safety Data First Aid SKIN: Flush with water. Wipe off. INGESTION: No first aid should be needed. EYES: Flush with water. Fire FLASH OINT: Above 0. C. (closed cup) Explosive roperties: No Suitable Extinguishing Media: Carbon Dioxide Foam, Dry owder or fine water spray. Water can be used to cool fire exposed containers. Environment Do not allow large quantities to enter drains or surface waters. Methods for cleaning up: Scrape up and place in suitable container fitted with a lid. The spilled product produces an extremely slippery surface. Harmful to aquatic organisms and may cause longterm adverse effects in the aquatic environment. However, due to the physical form and water insolubility of the product the bioavailability is negligible. Handling General ventilation is recommended. Avoid skin and eye contact. Storage Do not store with oxidizing agents. Keep container closed and store away from water or moisture. Molykote Grease Safety Data First Aid SKIN: No first aid should be needed. INGESTION: No first aid should be needed. EYES: No first aid should be needed. INHALATION: No first aid should be needed. Fire FLASH OINT: Above 0. C. (closed cup) Explosive roperties: No Suitable Extinguishing Media: Carbon Dioxide Foam, Dry owder or fine water spray. Water can be used to cool fire exposed containers. Environment No adverse effects are predicted. Handling General ventilation is recommended. Avoid eye contact. Storage Do not store with oxidizing agents. Keep container closed and store away from water or moisture.
Servicing the Tool English Service Kits For all servicing we recommend the use of the following service kits. SERVICE KIT : 00005300 Spanners are specified in inches and across flats unless otherwise stated. ITEM ART Nº DESCRITION Nº OFF ITEM ART Nº DESCRITION Nº OFF 000005 CIRCLI LIERS 0000035 SEAL REMOVAL HOOK 00000006 SATULA 000000 BARREL LUG REMOVAL SANNER 00000446 EXTRACTOR 000005 BULLET 00000603 BARREL VICE JAWS 0000043 SCREWDRIVER 0000050 3 /" ROD 00000 INTENSIFIER SANNER 000005 /4" ROD 0000003 /" ALLEN KEY 0000060 'O' RING ASSEMBLY BULLET 000006 R LOCTITE MULTIGASKET 54 50ml ACK 0000055 mm SANNER 0000046.5mm ALLEN KEY 00000434 3mm SANNER 0000035 3mm ALLEN KEY 000003 3 /" x 5 /6" B.S.W. SANNER 000004 4mm ALLEN KEY 000000 /6" x 5 /" SANNER 000005 5mm ALLEN KEY 0000000 /6" x /" SANNER 00000 0g TIN MOLY LITHIUM GREASE E 353 SERVICE KIT : 00 ART Nº DESCRITION 0000066 ISTON SLEEVE 000006 TRIGGER VALVE EXTRACTOR 0000060 BULLET 000006 'T' SANNER 0000006 'T' SANNER SIGOT 0000064 GUIDE TUBE 0000065 INSERTION ROD 0000035 3 MM ALLEN KEY 0000046.5 MM ALLEN KEY 000005 MM IN UNCH Spanners are specified in inches and across flats unless otherwise stated. Nº OFF ART Nº DESCRITION Nº OFF 000005 CIRCLI LIERS 0000000 /6 x / SANNER 000000 /6 x 5 / SANNER 0000005 5 / x /6 SANNER 0000066 EG SANNER 000006 SEAL EXTRACTOR 000006 STO NUT 0000000 RIMING UM 00000 GREASE MOLY LITHIUM E..353 00005 GREASE MOLYKOTE 55M 000005 GREASE MOLYKOTE 3
Maintenance Every 500,000 cycles the tool should be completely dismantled and new components should be used where worn, damaged or when recommended. All O rings and seals should be renewed and lubricated with Molykote 55m grease for pneumatic sealing or Molykote III for hydraulic sealing. IMORTANT Safety Instructions appear on page 4. The employer is responsible for ensuring that tool maintenance instructions are given to the appropriate personnel. The operator should not be involved in maintenance or repair of the tool unless properly trained. The airline must be disconnected before any servicing or dismantling is attempted, unless specifically instructed otherwise. It is recommended that any dismantling operation be carried out in clean conditions. rior to dismantling the tool, you will need to remove the nose equipment. For total tool servicing we advise that you proceed with the dismantling of subassemblies in the order shown. Dismantling 0530000 REMOVAL OF THE HEAD MOULDINGS Manually flip the Clip 4 up and remove the End Cap 50. Using an Allen Key*, remove the three body moulding securing Screws and Nuts from the tool body and one Screw from the LH Body Moulding 60. Remove the RH and LH Body Moulding 5 and 60. Assemble in reverse order of dismantling. NEUMATIC ISTON ASSEMBLY Clamp the Body of the inverted tool across the air inlet bosses in a vice fitted with soft jaws. ull off the Rubber Boot 6. Using the peg spanner* unscrew Base Cover 3. Unscrew Locknuts 6 ( off) and remove the Base late. Remove the Cylinder Liner 5, together with Sealing Washers ( off) and O Rings (off). Remove neumatic iston Assembly 5 from Body together with O Ring, Lip Seal (3 off) and Guide Ring. Assembly in reverse order. VALVE SOOL ASSEMBLY Remove neumatic iston Assembly 5 and Intensifier Seal Assembly as described immediately above. Using the T spanner* and T spanner spigot* undo Clamp Nut 64 and remove it together with Top late 6, Tie Rods 4 and Transfer Tube Assembly 6. Release the tool from the vice and separate Body with O Ring 0 from Handle Assembly 5. ull off the Head Assembly 56 from Handle Assembly 5 and remove O Ring from the intensifier tube. ush out Valve Seat 6 together with both O Rings ( off). Remove all the components of Valve Spool Assembly 6. Finally remove O Ring out of the handle counter bore. Assemble in reverse order to dismantling ensuring that the central port in Valve Seat 6 faces upwards towards O Ring. TRIGGER Using the millimeter diameter pin punch*, drive Trigger in 65 out and lift off Trigger 6. Unscrew Trigger Valve 4 using the trigger valve extractor*. Assemble in reverse order to dismantling. * Refers to items included in the service kits 00005300 & 00. For complete list see page 3. Item numbers in bold refer to the general assemblies and parts lists on pages 6. 4
Maintenance English Dismantling 0530000 TAIL JAW CYLINDER Using an Allen Key*, remove one cap head Screw 5 ensuring that any trapped air in the tail jaw cylinder is exhausted. Remove the second cap head Screw 5. ull out Rear lug 4. Extract air tail jaw components, comprising Tail Jaw iston Assembly 5, Spring 35, Jaws 34 and Jaw Housing 4. Remove plug at rear of piston assembly using an Allen Key* and a bar through the large slot in the turret. Clean out turret using a 4.mm ( 3 /6 ) drill and replace plug using a nonhardening sealing compound, e.g. Loctite Multigasket 54*. Remove piston seal O Ring 0. Grip Barrel 44 in a vice using soft jaws* to avoid damage. Using a box spanner*, unscrew Barrel lug 45, preventing Barrel 44 turning by using an open ended spanner*. Disconnect Air Tail Jaw Concertina Tube 54 from Head Assembly and pull Tail Jaw Cylinder 46 from tool. Remove O Ring 3, Rubbing Strip 40 and Barrel Return Spring 3. Free length of Spring 35 should be 3.mm (.5 ). Replace if necessary. Coat the tail jaws with MolyLithium grease before assembling. Assemble in reverse order of dismantling. HYDRAULIC ISTON Remove Tail Jaw Cylinder 46 as described earlier. Grip Head Assembly 56 in vice using soft jaws* to avoid damage, undo Stroke Limiter 3. Using an Allen Key*, loosen Screw 3 clamping the Switch Block 55 to the Barrel 44. Using an Allen Key*, remove the Switch Block 55 & O Ring, by undoing the securing Screw 4. Hold the tool firmly and pull the Barrel 44 from the body (a small quantity of hydraulic oil may be ejected from inside body). Remove iston 3 carefully so as not to damage body bore. Remove Lip Seal 5. Lip Seal 6 is difficult to remove without damaging, but can remain in place during cleaning (provided it is not affected by cleaning process). If however, Lip Seal 6 requires renewing proceed as follows: Using spatula*, prise out Lip Seal 6 from Head Assembly 56, taking care not to damage head cavity and bores. The removed Lip Seal 6 MUST be discarded. To replace Lip Seal 6, unscrew existing Bleed lug 43 until inside face is level with internal bore of the Head Assembly 56. This will provide a smooth passage for insertion of new Lip Seal 6 through rear of body. Ensure the Lip Seal 6 is well greased and the correct way round with the open end of the seal facing the rear tail jaws. Complete assembly in reverse order of dismantling. TAIL JAW ON/OFF VALVE The unit is designed so that minimum of servicing is required during the life of the tool. If it is necessary to dismantle valve, proceed as follows: Remove Switch Block 55 as described in section Hydraulic iston. Using a screwdriver*, carefully remove the Chrome Starlock Washer from Air Tail Jaw Spool 4 and discard washer. Extract Air Tail Jaw Spool 4 from Switch Block 55. Taking care not to damage the Air Tail Jaw Spool 4, remove the O Rings. Clean spool and refit new O Rings using assembly bullet* and insert into Switch Block 55, noting its orientation. Fit New Chrome Starlock Washer by clamping in vice using a soft jaw vice to prevent damage. DO NOT USE UNDUE FORCE. Complete assembly in reverse order of dismantling. HANDLE and END CA Clean and inspect mouldings for cracks or other damage. CURSOR Clean and oil Mechanical Cursor 36 occasionally with a little light oil. IMORTANT Check the tool against daily and weekly servicing. riming is ALWAYS necessary after the tool has been dismantled and prior to operating. * Refers to items included in the service kits 00005300 & 00. For complete list see page 3. Item numbers in bold refer to the general assemblies and parts lists on pages 6. 5