Nosturin kasausohjeet Crane assembly instructions 17.1.2014 10.2.2014 1
Nosturin osat Crane sub-assemblies Vetopuomi 6,1t Pulling boom 6,1t Tukisauva Support beam 0,9t / kpl 0,9t / pcs Liikkuva vastapaino 75-80t Moving counterweight 75-80t Säteiskoneisto Radial mechanism 13t 13t Nokkapuomi Jib boom 25t 25t Kääntövaunu 135t Slewing carriage 135t Konehuoneen vastapaino 85t Engine room counterweight 85t Hoitotaso 2t Service platform 2t Kantapuomi 26,5t Outrigger boom 26,5t Ohjaamo Cabin Kääntökehän laakeri 4,6t Slewing part bearing 4,6t Torni Tower 5t 5t 17t 17t Myrskylukko 0,4t Storm lock 0,4t Portaali Portal Telit Bogies 82t 82t 14,5t/kpl 14,5t/pcs 10.2.2014 2
1. Telien sijoittelu raiteille ja tuenta 1. Bogie placement and supporting on the tracks 10 500 mm 8604 mm Existingsupportscanbeusedin all bogies 4430 mm 10.2.2014 3
2. Portaalin / telistön asennus 2. Portal/ bogies assembly Portaali Portal 82t 82t 4kpl nostopisteitä app. 20,5t/1 4pcs lifting points Stormlock assembly, may be done later Auxiliarguideplateshelpsfor placement. Rod, ifused, may damagethe thread in hole. 10.2.2014 4
3. Tornin ja kierreportaiden asennus porttaaliin 3. Tower and helical stairs erection to portal Torni / Tower 17t 4 kpl nostopisteitä 4 pcslifting points, app. 4,3t / 1 liftingpoint Special bolt connection assembly. Bearing assembly for radial forces on lower end, From top, supported mechanically to slewing machinery room structure(takes the staircase weight). 10.2.2014 5
4. Kääntökehän laakerin asennus 4. Slewing parts bearing mounting Slewinggearassemblyon top, before lifting the tower, may be more practical. 10.2.2014 6
5. Kääntövaunun asennus 5. Slewing carriage mounting Kääntövaunu Slewing carriage 135t 135t 4kpl nostopisteitä 4pcs lifting points ~34t / nostopiste lifting point 100 pcs of M36 bolts/each round 10.2.2014 7
6. Kiinteän vastapainon asennus 6. Fixed counterweight assembly Konehuoneen vastapaino Machinery room counterweight 85t 85t 2 kpl nostopisteitä 2pcs lifting points 42,5t / lifting point- nostopiste 10.2.2014 8
7. Säteiskoneiston asennus 7. Boom drive mechanism assembly 10.2.2014 9
8. Kantapuomin nivelen asennus 8. Main boom joint assembly Kantapuomi 26,5t Main boom 26,5t 4 kpl nostopisteitä 4pcs lifting points ~6,7t / nostopiste lifting point To avoid high mobile crane costs, one posibility is to use auxiliar support tower, while fitting the jib joint. 10.2.2014 10
Nokkapuomi Jib 25t 25t 3kpl nostopisteitä 3pcs lifting points 8,3t / nostopiste lifting point 9. Nokkapuomin asennus 9. Jib mounting Donothit the ground! 10.2.2014 11
10. Tuenta nokkapuomista laituria vasten 10. Supportingmain and jibboomfromjibboomagainstthedock Nokkapuomi lukitaan vaijerillasopivaan kulmaan, ajatellen vetopuomin ja säteiskoneiston asennusta. Jibboomcanberestrainedto rightposition with cablewire, sothatthe angleis right for pullingboomand boomdrivemachineryassembly. Vaijeri Cable wire App.+95 10.2.2014 12
11. Vetopuomin nivelen kiinnitys nokkapuomiin 11. Pulling boom joint mounting to main boom Vetopuomi/ Pulling boom 6,1t Vaijeri Cable wire + 95 10.2.2014 13
2 12. Puomistoasennus 12. Boom assembly 1 Vaijeri Cable wire 1. Puomit, nosto ylös 2. Vetopuomin saatto ja nivel torniin kiinni 2 1. Liftboomsystemup 2. Pulling boom joint assembly to tower structure 10.2.2014 14
13. Puomisto pidetään kannatettuna, säteiskoneiston nivelten kiinnityksen ajan 13. Boom system must be kept lifted, while fitting the boom drive mecanisms joints 1 2 Vaijeri Cable wire 1. Pidä puomisto kannatettuna / keep boom system lifted 2. Säteiskoneiston aisat ulos ja niveltapit paikolleen / boom drive machinery fitting 10.2.2014 15
Huom! Laakeripintoja ei saa käyttää nostoissa! Note! Bearing surfaces can not be used for lifting! 14.Liikkuvan vastapainon asennus ja tukivarren yläpään kiinnitys 14. Moving counterweight and support beams upper joint mounting Vastapainoa kannatellaan asennuksen ajan Counterweightis supported during mounting Tukisauva Support beam 0,9t / kpl 0,9t / pcs Liikkuva vastapaino 75-80t Moving counterweight 75-80t 2kpl nostopisteitä 2pcs lifting points ~40t / nostopiste lifting point 10.2.2014 16
Vastapainoa kannatellaan nosturilla tai tuetaan tornia vasten, asennuksen ajan. Counterweight can be supported, fromtop bythe crane or mechanically against the tower, during mounting 15. Tukisauvojen asennus 15. Support beam mounting Säteiskoneiston varsia voidaan liikuttaa tunkkien avulla. Radialmechanismsarmscanbemovedbyjacks. 10.2.2014 17
16. Asennusaikaisten tukien poisto 16. Removal of the assembly supports 0 5 10 15 20 n. 31 m n. 61 m n. 12 m n. 37 m 10.2.2014 18
17. Ohjaamon asennus ja tasot 17. Mounting of the cabin and access platforms 10.2.2014 19
17. Ohjaamon asennus ja tasot 17. Mounting of the cabin and access platforms 10.2.2014 20