1(17) NDT-STANDARDIEN TILANNEKATSAUS YLEISTÄ Eurooppalaiset NDT-standardit laaditaan komiteassa CEN/TC 138 Non-destructive testing ja kansainväliset NDT-standardit komiteassa ISO/TC 135. Hitsaukseen liittyvät NDTstandardit laaditaan alakomiteassa CEN/TC 121/SC 5 Non-destructive testing of welds ja ISO/TC 44/SC 5 Testing and inspection of welds. Nämä standardit ovat ns. horisontaaleja standardeja, joihin tuotestandardeissa tarvittaessa viitataan. Luettelon lopussa on kaavio NDT-standardeja koskevasta järjestelmästä. Sen lisäksi laaditaan NDT-standardeja myös levyille, putkille, valuille ja takeille. Komiteat CEN/TC 138 ja CEN/TC 121/SC 5 tekevät kiinteästi yhteistyötä ja ne ovat perustaneet kullekin NDT-menetelmälle työryhmät. Organisaatio näkyy alla olevasta taulukosta, jossa suluissa oleva maa toimii sihteeristönä. Yleiset NDT-standardit CEN/TC 138 (FR) WG 1 Radiografia (DE) WG 2 Ultraääni (DE) WG 3 Pyörrevirta (FR) WG 4 Tunkeumaneste (DE) WG 5 Magneettijauhe (ES) WG 6 Vuototestaus (IT) WG 7 Akustinen emissio (IT) WG 8 Silmämääräinen tarkastus (UK) WG 10 Röntgensädediffraktio (IT) WG 11 Lämpökuvaus (DE) WG 12 Näöntarkkuus (UK) Hitsaukseen liittyvät NDT-standardit CEN/TC 121/SC 5 (FR) WG 1 Radiografia (DE) WG 2 Ultraääni (DE) WG 3 Pyörrevirta (DE) WG 4 Tunkeumaneste (DE) WG 5 Magneettijauhe (FI) WG 6 Silmämääräinen (UK) WG 7 Rikkova aineenkoetus (DE) Hitsaukseen liittyvän NDT-standardisoinnin painopiste on ISOssa (ISO/TC 44/SC 5). Toistaiseksi alakomiteassa toimivat kaksi työryhmää WG 1 Radiografia ja WG 2 Ultraääni. Edellä mainittujen CENin ja ISOn teknisten komiteoiden, alakomiteoiden ja työryhmien toimintaa seurataan METSTAn kansallisissa standardisointikomiteoissa K 81 Radiografia, K 89 Ultraääni ja K 106 Pintamenetelmät. Nämä standardisointikomiteat vastaavat aihealueidensa standardiehdotuksiin liittyvistä päätöksistä ja niihin lähetettävistä Suomen kannanotoista sekä osallistuvat suomenkielisten käännösten valmisteluun. Komiteoiden K 81, K 89 ja K 106 toimintaan osallistuminen on maksutonta. Seuraavassa luettelossa esitetään standardisointitilannetta menetelmittäin. Kaikki EN- ja -standardit vahvistetaan Suomessa SFS-EN ja SFS- -standardeiksi. Mikäli standardin otsikko on esitetty suomeksi, se on saatavissa myös suomenkielisenä käännöksenä. Julkaistut standardit (EN ja ISO) voi tilata Suomen Standardisoimisliitosta, http://sales.sfs.fi. Lausuntovaiheen ehdotukset (pren ja ISO/DIS) ovat lausuntokierroksen aikana veloituksetta luettavissa SFS:n Lausuntopyyntöpalvelussa, http://lausunto.sfs.fi. Lisätietoja: Mika Vartiainen, Metalliteollisuuden Standardisointiyhdistys ry, METSTA, puh. 040 544 1579, etunimi.sukunimi@metsta.fi, http://www.metsta.fi.
2(17) RADIOGRAFIA YLEISSTANDARDIT EN 1330-3 EN 1330-11 5579 19232-1 19232-2 19232-3 19232-4 19232-5 11699-1 11699-2 EN 12543-1 EN 12543-2 EN 12543-3 EN 12543-4 EN 12543-5 Rikkomaton aineenkoetus. Sanasto. Osa 3: Teollisuusradiografiassa käytetyt termit NDT - Terminology - Part 11: X-ray diffraction from polycrystalline and amorphous materials Rikkomaton aineenkoetus. Metallisten materiaalien radiografinen kuvaus käyttäen filmitekniikkaa ja röntgen- tai gammasäteilyä. Perusohjeet (korvannut standardin EN 444) NDT - Image quality of radiographs - Part 1: Image quality indicators (wire type) - Determination of image quality value (korvannut standardin EN 462-1) NDT - Image quality of radiographs - Part 2: Concepts, image quality indicators (step and hole type), determination of image quality value (korvannut standardin EN 462-2) NDT - Image quality of radiographs - Part 3: Image quality classes for ferrous metals (korvannut standardin EN 462-3) NDT - Image quality of radiographs - Part 4: Experimental evaluation of image quality values and image quality tables (korvannut standardin EN 462-4) NDT - Image quality of radiographs - Part 5: Image quality indicators (Duplex wire type), determination of total image unsharpness value (korvannut standardin EN 462-5) NDT - Industrial radiographic film - Part 1: Classification of films systems for industrial radiography (korvannut standardin EN 584-1) Industrial radiographic film - Part 2: Control of film processing by means of reference values (korvannut standardin EN 584-2) Characteristics of focal spots in industrial X-ray tube assemblies. Part 1: Scanning method Characteristics of focal spots in industrial X-ray tube assemblies. Part 2: Pinhole camera radiographic method Characteristics of focal spots in industrial X-ray tube assemblies. Part 3: Slit camera radiographic method Characteristics of focal spots in industrial X-ray tube assemblies. Part 4: Edge method Characteristics of focal spots in industrial X-ray tube assemblies. Part 5: Measurement of effective focal spot size of mini and microfocus X-ray tubes used for industrial radiography
3(17) EN 12544-1 EN 12544-2 Evaluation and determination of the X-ray voltage. Part 1: Voltage divider method Measurement and evaluation of the X-ray voltage. Part 2: Constancy check by the thick filter method EN 12544-3 Measurement and evaluation of the X-ray tube voltage. Part 3: Spectrometric method EN 12679 EN 13068-1 EN 13068-2 EN 13068-3 EN 13925-1 EN 13925-2 EN 13925-3 NDT - Determination of the size of industrial radiographic sources - Radiographic method NDT- Radioscopic testing - Part 1: Quantitative measurement of imaging properties NDT - Radioscopic testing - Part 2: Qualitative control and long term stability of imaging devices General principles of radioscopic testing of construction materials by X- and gamma rays NDT - X- ray diffraction from polycrystalline and amorphous material - Part 1: General principles NDT - X- ray diffraction from polycrystalline and amorphous material - Part 2: Procedures NDT - X-ray diffraction from polycrystalline and amorphous materials - Part 3: Instruments EN 14096-1 NDT - Qualification of radiographic film digitization systems - Part 1: Definitions, quantitative measurements of image quality parameters, standard reference film and qualitative control EN 14096-2 NDT - Qualification of radiographic film digitization systems - Part 2: Minimum requirements for digitization systems according to the application field EN 14784-1 EN 14784-2 EN 15305 EN 16016-1 EN 16016-2 EN 16016-3 EN 16016-4 NDT - Industrial computed radiography with storage phosphor imaging plates - Part 1: Classification of systems NDT - Industrial computed radiography with storage phosphor imaging plates - Part 2: General principles for testing of metallic materials using X-rays and gamma rays NDT - Test method for measurement of residual stress by X-ray diffraction NDT - Radiation method - Computed tomography - Part 1: Terminology NDT - Radiation method - Computed tomography - Part 2: Principle, equipment and samples NDT - Radiation methods - Part 3: Operation and interpretation NDT - Radiation methods - Part 4: Qualification
4(17) EN 25580 ISO 16371-1 C/TS 21432 NDT - Industrial radiographic illuminators - Minimum requirements (ISO 5580) NDT - Industrial computed radiography with storage phosphor imaging plates - Part 1: Classification of systems (EN 14784-1) NDT - Test method for measurement of residual stress by neutron diffraction ISO/DIS 15708-1 NDT - Radiation methods - Computed tomography - Part 1: Principle, equipment and samples (EN 16016-1) ISO/DIS 15708-2 NDT - Radiation methods - Computed tomography - Part 2: Operation and interpretation (EN 16016-2) ISO/DIS 15708-3 NDT - Radiation methods - Computed tomography - Part 3: Terminology (EN 16016-3) ISO/DIS 15708-4 NDT - Radiation methods - Computed tomography - Part 4: Qualification (EN 16016-4) pr 16371-2 NDT - Industrial computed radiography with storage phosphor imaging plates - Part 2: General principles for testing of metallic materials using X-rays and gamma rays Työn alla: pr 11699-2 Revision of 11699-2 pr 19232-5 Revision of 19232-5 pr 21432 NDT - Standard test method for determining residual stresses by neutron diffraction (revision of C/TS 21432) HITSIT 10675-1 10675-2 Hitsien rikkomaton aineenkoetus. Radiografisen kuvauksen hyväksymisrajat. Osa 1: Teräs, nikkeli, titaani ja niiden seokset (korvannut standardin EN 12517-1) Hitsien rikkomaton aineenkoetus. Radiografisen kuvauksen hyväksymisrajat. Osa 2: Alumiini ja niiden seokset (korvannut standardin EN 12517-2) 17636-1 Hitsien rikkomaton aineenkoetus. Radiografinen kuvaus. Osa 1: Röntgen- ja gammakuvaus filmitekniikalla (korvannut standardin EN 1435) 17636-2 Hitsien rikkomaton aineenkoetus. Radiografinen kuvaus. Osa 2: Röntgen- ja gammakuvaus digitaalitekniikalla (korvannut standardin EN 1435)
5(17) pr 10675-1 Revision of 10675-1 pr 10675-2 Revision of 10675-2 VALUT EN 12681 Valut. Radiografinen tarkastus pren 12681-1 pren 12681-2 Founding - Radiographic testing - Part 1: Film techniques (revision of EN 12681) Founding - Radiographic testing - Part 2: Techniques with digital detectors PUTKET 10893-6 10893-7 NDT of steel tubes - Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections (korvannut standardin EN 10246-10) NDT of steel tubes - Part 7: Digital radiographic testing of the weld seam of welded steel tubes for the detection of imperfections EN 16407-1 Radiographic inspection of corrosion and deposits in pipes by X- and gamma rays - Part 1: Tangential radiographic inspection EN 16407-2 Radiographic inspection of corrosion and deposits in pipes by X- and gamma rays - Part 2: Double wall radiographic inspection Työn alla: pr 10893-6 Revision of 10893-6 pr 10893-7 Revision of 10893-7 ULTRAÄÄNI YLEISSTANDARDIT EN 1330-4 EN 16018 16810 Rikkomaton aineenkoetus. Sanasto. Osa 4: Ultraäänitarkastuksessa käytetyt termit (2. painos) Rikkomaton aineenkoetus. Sanasto. Vaiheistetussa ultraäänitarkastuksessa käytettävät termit Rikkomaton aineenkoetus. Ultraäänitarkastus. Yleisperiaatteet (korvannut standardin EN 583-1)
6(17) 16811 16823 16826 16827 16828 2400 7963 16946 18563-1 18563-3 EN 12668-1 EN 12668-2 EN 12668-3 EN 14127 EN 15317 EN 16392-2 CEN/TR 15134 ISO 12715 ISO 16809 Ultrasonic examination - Sensitivity and range setting (korvannut standardin EN 583-2) Rikkomaton aineenkoetus. Ultraäänitarkastus. Läpäisytekniikka (korvannut standardin EN 583-3) Rikkomaton aineenkoetus. Ultraäänitarkastus. Pystysuunnassa olevien epäjatkuvuuskohtien tarkastus (korvannut standardin EN 583-4) Ultrasonic examination - Characterization and sizing of discontinuities (korvannut standardin EN 583-5) Ultrasonic examination - Time-of-flight diffraction technique (korvannut standardin EN 583-6) Rikkomaton aineenkoetus. Ultraäänitarkastus. Tarkistuskappale 1 (korvannut standardin EN 12223) Rikkomaton aineenkoetus. Ultraäänitarkastus. Tarkistuskappale 2 (korvannut standardin EN 27963) NDT - Ultrasonic testing - Specification for step wedge calibration block NDT - Characterization and verification of ultrasonic phased array systems - Part 1: Instruments NDT - Characterization and verification of ultrasonic phased array systems - Part 3: Combined systems Ultrasonic examination - Characterization and verification of ultrasonic examination equipment - Part 1: Instruments (2. painos) Ultrasonic examination - Characterization and verification of ultrasonic examination equipment - Part 2: Probes (2. painos) Rikkomaton aineenkoetus. Ultraäänilaitteiden ominaisuuksien todentaminen. Osa 3: Ultraäänilaitteisto (2. painos) Rikkomaton aineenkoetus. Paksuusmittaus ultraäänellä (2. painos) NDT - Ultrasonic testing - Characterization and verification of ultrasonic thickness equipment NDT - Characterization and verification of ultrasonic phased array systems - Part 2: Probes NDT - Automated ultrasonic examination - Selection and application of system NDT - Ultrasonic testing - Reference blocks and test procedures for the characterization of contact probe sound beams NDT - Ultrasonic thickness measurement
7(17) ISO 18211 NDT - Long-range inspection of above-ground pipelines and plant piping using guided wave testing with axial propagation Fpr 5577 NDT - Ultrasonic testing - Vocabulary (Revision of EN 1330-4) ISO/FDIS 19675 NDT - Ultrasonic testing - Specification for calibration block for phased array ultrasonic testing pr 18563-2 NDT - Characterization and verification of ultrasonic phased array systems - Part 2: Probes pr 16946 Revision of 16946 Työn alla: ISO/DIS 21453 ISO/DTR 16829 NDT - Test method for measuring residual stress using ultrasonic critical refracted longitudinal wave NDT - Automated ultrasonic testing - Selection and application of systems HITSIT 10863 11666 13588 15626 17405 17640 22825 23279 Welding - Use of time-of-flight diffraction technique (TOFD) for examination of welds (korvannut spesifikaation CEN/TS 14751) Hitsien rikkomaton aineenkoetus. Hitsausliitosten ultraäänitarkastus. Hyväksymisrajat (korvannut standardin EN 1712) NDT of welds. Ultrasonic testing. Use of automated phased array technology NDT of welds. Time of flight diffraction technique (TOFD). Acceptance levels (korvannut standardin EN 15617) NDT - UT - Technique of testing claddings produced by welding, rolling and explosion Hitsien rikkomaton aineenkoetus. Ultraäänitarkastus. Tekniikat, tarkastustasot ja arviointi (korvannut standardin EN 1714) Rikkomaton aineenkoetus. Ultraäänitarkastus. Austeniittisten ja nikkelipohjaisten hitsien tarkastus (2. painos) Hitsien rikkomaton aineenkoetus. Hitsien ultraäänitarkastus. Hitsausvirheiden tyypin määrittäminen (2. painos, korvannut standardin EN 1713) pr 23279 Revision of 23279
8(17) pr 17640 Revision of 17640 pr 19285 NDT of welds - Phased array technique (PA) - Acceptance levels Työn alla: pr 11666 Revision of 11666 pr 20601 NDT of welds - Ultrasonic testing - Use of (semi-)automated phased array technology for steel components with small wall thickness pr 22825 Revision of 22825 VALUT EN 12680-1 EN 12680-2 EN 12680-3 Valut. Ultraäänitarkastus. Osa 1: Teräsvalut yleiseen käyttöön Valut. Ultraäänitarkastus. Osa 2: Teräsvalut suuresti rasitettuihin kohteisiin Valut. Ultraäänitarkastus. Osa 3: Pallografiittirautavalut (2. painos) PUTKET 10893-8 10893-9 10893-10 10893-11 10893-12 NDT of steel tubes - Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections (korvannut standardit EN 10246-14, -16 ja -17) NDT of steel tubes - Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the manufacture of welded steel tubes (korvannut standardin EN 10246-15) NDT of steel tubes - Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections (korvannut standardit EN 10246-6 ja -7) NDT of steel tubes - Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections (korvannut standardit EN 10246-8 ja -9) NDT of steel tubes - Part 12: Automated full peripheral ultrasonic thickness testing of seamless and welded (except submerged arc-welded) steel tubes (korvannut standardin EN 10246-13) TAKEET EN 10228-3 NDT of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings (2. painos)
9(17) EN 10228-4 NDT of steel forgings - Part 4: Ultrasonic testing of austenitic or austenitic-ferritic stainless steel forgings (2. painos) LEVYT, TANGOT JA PROFIILIT EN 10160 EN 10306 EN 10307 EN 10308 ISO 17577 Vähintään 6 mm paksujen teräslevytuotteiden ultraäänitarkastus (Heijastusmenetelmät) Iron and steel - Ultrasonic testing of broad flanged beams with parallel flanges and IPE beams NDT - Ultrasonic testing of austenitic and austenitic-ferritic stainless steels flat products of thickness equal to or greater than 6 mm (reflection method) Rikkomaton aineenkoetus. Terästankojen ultraäänitarkastus Steel - Ultrasonic testing for steel flat products of thickness equal to or greater than 6 mm (2. painos) PYÖRREVIRTATARKASTUS YLEISSTANDARDIT 12718 15549 15548-1 15548-2 15548-3 Rikkomaton aineenkoetus. Pyörrevirtatarkastus. Sanasto (korvannut standardin EN 1330-5) Eddy current examination - General principles and basic guidelines (korvannut standardin EN 12084) Eddy current testing - Equipment characteristics and verification - Part 1: Instrument characteristics and verification (2. painos) Eddy current testing - Equipment characteristics and verification - Part 2: Probe characteristics and verification (2. painos) Eddy current testing - Equipment characteristics and verification - Part 3: System characteristics and verification (korvannut standardin EN 13860-3) pr 20339 ISO/DIS 20669 NDT - Equipment for eddy current examination - Array probe characteristics and verification NDT - Pulsed eddy current testing of ferromagnetic material components HITSIT
10(17) 17643 NDT of welds - Eddy current examination of welds by complex plane analysis (2. painos, korvannut standardin EN 1711) PUTKET 10893-2 EN 1971-1 EN 1971-2 NDT of steel tubes - Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections (korvannut standardin EN 10246-3) Copper and copper alloys - Eddy current test for measuring defects on seamless round copper and copper alloy tubes - Part 1: Test with an encircling test coil on the outer surface (korvannut standardin EN 1971) Copper and copper alloys - Eddy current test for measuring defects on seamless round copper and copper alloy tubes - Part 2: Test with an internal probe on the inner surface PINNOITTEET 2360 21968 Epämagneettisten sähköä johtavien perusaineiden sähköä johtamattomat pinnoitteet. Paksuuden mittaus. Amplitudin mittaukseen perustuva pyörrevirtamenetelmä Metallisten ja ei-metallisten perusaineiden epämagneettiset metalliset pinnoitteet. Paksuuden mittaus. Vaiheen mittaukseen perustuva pyörrevirtamenetelmä pr 2360 Revision of 2360 TUNKEUMANESTETARKASTUS YLEISSTANDARDIT 12706 3059 Rikkomaton aineenkoetus. Tunkeumanestetarkastus. Sanasto (2. painos) Rikkomaton aineenkoetus. Tunkeumaneste- ja magneettijauhetarkastus. Katseluolosuhteet (2. painos) 3452-1 Rikkomaton aineenkoetus. Tunkeumanestetarkastus. Osa 1: Yleisperiaatteet (korvannut standardin EN 571-1) 3452-2 NDT - Penetrant testing - Part 2: Testing of penetrant materials (2. painos) 3452-3 NDT - Penetrant testing - Part 3: Reference test blocks (2. painos)
11(17) 3452-4 3452-5 3452-6 CEN/TR 16638 NDT - Penetrant testing - Part 4: Equipment NDT - Penetrant testing - Part 5: Penetrant testing at temperatures higher than 50 C NDT - Penetrant testing - Part 6: Penetrant testing at temperatures lower than 10 C NDT - Penetrant and magnetic particle testing using blue light Työn alla: pren xxxxx pren xxxxx NDT - Lighting in penetrant and magnetic particle testing, good practice NDT - Penetrant testing: reference photographs and sizing of indications HITSIT 23277 Hitsien rikkomaton aineenkoetus. Hitsien tunkeumanestetarkastus. Hyväksymisrajat (2. painos) VALUT EN 1371-1 EN 1371-2 Valut. Tunkeumanestetarkastus. Osa 1: Hiekka-, kokilli- ja matalapainevalut (2. painos) Valut. Tunkeumanestetarkastus. Osa 2: Tarkkuusvalut (2. painos) PUTKET 10893-4 NDT of steel tubes - Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface imperfections (korvannut standardin EN 10246-11) TAKEET EN 10228-2 NDT of steel forgings - Part 2: Penetrant testing (2. painos) MAGNEETTIJAUHETARKASTUS YLEISSTANDARDIT 12707 Rikkomaton aineenkoetus. Magneettijauhetarkastus. Sanasto (Korvannut standardin EN 1330-7) 9934-1 Rikkomaton aineenkoetus. Magneettijauhetarkastus. Osa 1: Yleisohjeet (2. painos)
12(17) 9934-2 NDT - Magnetic particle testing - Part 2: Detection media (2. painos) 9934-3 NDT - Magnetic particle testing - Part 3: Equipment (2. painos) Fpr 9934-1 Revision of 9934-1 HITSIT 17638 23278 Hitsien rikkomaton aineenkoetus. Magneettijauhetarkastus (korvannut standardin EN 1290) Hitsien magneettijauhetarkastus. Hyväksymisrajat (2. painos) pr 17638 Revision of 17638 VALUT EN 1369 Valut. Magneettijauhetarkastus (2. painos) PUTKET 10893-5 NDT of steel tubes - Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections (korvannut standardit EN 10246-12 ja -18) TAKEET EN 10228-1 NDT of steel forgings - Part 1: Magnetic particle inspection (2. painos) SILMÄMÄÄRÄINEN TARKASTUS YLEISSTANDARDIT EN 1330-10 EN 13018 EN 13927 Rikkomaton aineenkoetus. Sanasto. Osa 10: Silmämääräisessä tarkastuksessa käytettävät termit NDT - Visual testing - General principles (2. painos) NDT - Visual testing - Equipment HITSIT
13(17) 17637 Hitsien rikkomaton aineenkoetus. Sulahitsausliitosten silmämääräinen tarkastus (korvannut standardin EN 970) pr 17637 Revision of 17637 VALUT EN 1370 Valut. Pinnan tilan tarkastus (2. painos, korvannut standardit EN 12454 ja EN 1370) VUOTOTESTAUS YLEISSTANDARDIT EN 1330-8 EN 1518 EN 1593 EN 1779 EN 13184 EN 13185 EN 13192 EN 13625 NDT - Terms used in leak tightness testing NDT - Leak testing - Characterization of mass spectrometer leak detector NDT - Leak testing - Bubble emission method NDT - Leak testing - Guide to the method selection NDT - Leak testing - Pressure change method NDT - Leak testing - Trace gas method NDT - Leak testing - Calibration of reference leaks for gases NDT - Leak testing - Guide to selection of instrumentation for the measurement of gas leakage Fpr 20484 NDT - Leak testing - Vocabulary pr 20485 pr 20486 NDT - Leak testing - Tracer gas method NDT - Leak testing - Calibration of reference leaks for gases PUTKET 10893-3 NDT of steel tubes - Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged arcwelded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections (korvannut standardit EN 10246-4 ja -5)
14(17) AKUSTINEN EMISSIO YLEISSTANDARDIT EN 1330-9 EN 13477-1 EN 13477-2 EN 13554 EN 14584 EN 15495 EN 15856 EN 15857 18081 ISO 18249 Rikkomaton aineenkoetus. Sanasto. Osa 9: Akustisessa emissiossa käytetyt termit (2. painos) Acoustic emission - Equipment characterisation - Part 1: Equipment description. Acoustic emission - Equipment characterisation - Part 2: Verification (2. painos) Acoustic emission - General principles (2. painos). Acoustic emission - Examination of metallic pressure equipment during proof testing - Planar location of AE sources (2. painos) Acoustic emission - Examination of metallic pressure equipment during proof testing - Zone locations of AE-sources Acoustic emission - General principles of acoustic emission testing of corrosion within metallic surrounding filled with liquid Acoustic emission - Testing of fibre-reinforced polymers - Specific methodology and general evaluation criteria NDT - Acoustic emission testing (AT) - Leak detection by means of acoustic emission NDT - Acoustic emission testing - Specific methodology and general evaluation criteria for testing of fibre-reinforced polymers pren 1330-9 Revision of EN 1330-9 ISO/DIS 19835 NDT - Acoustic emission testing - Steel structures of overhead travelling cranes and portal bridge cranes LÄMPÖKUVAUS EN 16714-1 EN 16714-2 EN 16714-3 ISO 10878 NDT - Thermographic testing - Part 1: General principles NDT - Thermographic testing - Part 2: Equipment NDT - Thermographic testing - Part 3: Terms and definitions NDT - Infrared thermography - Vocabulary ISO/FDIS 10880 NDT - Infrared thermographic testing - General principles
15(17) ISO/FDIS 18251-1 NDT - Infrared thermography - Part 1: Characteristics of system and equipment Työn alla: pren xxxxx ISO/WD 10893-13 NDT - Thermographic testing - Active thermography NDT of steel tubes - Part 13: Automated thermographic testing welded and seamless steel tubes as proof of tightness and imperfections NDT-HENKILÖSTÖN PÄTEVÖINTI 9712 18490 EN 4179 ISO 11484 CEN/TR 15589 CEN/TR 16332 ISO/TS 11774 ISO/TR 20807 ISO/TR 25107 ISO/TR 25108 ISO/TS 22809 Rikkomaton aineenkoetus. NDT-henkilöiden pätevöinti ja sertifiointi. Yleisperiaatteet (korvannut standardin EN 473) NDT - Evaluation of vision acuity of NDT personnel Aerospace series - Qualification and approval of personnel for non-destructive testing Steel products - Employer's qualification system for nondestructive testing (NDT) personnel NDT - Code of practice for the approval of NDT personnel by recognized third party organisations under the provisions of Directive 97/23/EC NDT - Interpretation of /IEC 17024 for NDT personnel certification application NDT - Perfomance based qualification NDT - Qualification of personnel for limited application of NDT NDT - Guidelines for NDT training syllabuses NDT - Guidelines for NDT personnel training organisations NDT - Discontinuity in the test specimens for use in qualification examinations Työn alla: prc/tr 25107 Revision of ISO/TR 25107 prc/tr 25108 Revision of ISO/TR 25108 ISO/WD 11484 Revision of ISO 11484 MUITA STANDARDISOINTIKOHTEITA EN 1330-1 NDT - Terminology - Part 1: General terms (2. painos)
16(17) EN 1330-2 17635 EN 12799 EN 16090 CEN/TR 15135 CR 13935 10893-1 ISO/TS 18173 ISO 24497-1 ISO 24497-2 ISO 24497-3 Rikkomaton aineenkoetus. Sanasto. Osa 2: NDT-menetelmien yhteiset termit (en fi de fr) Hitsien rikkomaton aineenkoetus. Yleisohjeet metallisille materiaaleille (korvannut standardin EN 12062) Brazing - Non-destructive examination brazed joints Copper and copper alloys - Estimation of average grain size by ultrasound Welding - Design and non-destructive testing of welds NDT - Generic NDE data format model NDT of steel tubes - Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel tubes for the verification of hydraulic leak tightness (korvannut standardit EN 10246-1 ja -2) NDT - General terms and definitions NDT - Metal magnetic memory - Part 1: General requirements NDT - Metal magnetic memory - Part 2: Terms and definitions NDT - Metal magnetic memory - Part 3: Inspection of welded joints Fpr 17635 Revision of 17635 PAINELAITTEIDEN TARKASTUS EN 13445-5 Lämmittämättömät painesäiliöt. Osa 5: Tarkastus ja testaus (5. painos (2014), issue 1) EN 13480-5 + A1 Metalliset teollisuusputkistot. Osa 5: Tarkastus ja testaus (2. painos (2013), issue 2) EN 12952-6 EN 12953-5 Vesiputkikattilat ja niihin liittyvät laitteistot. Osa 6: Kattilan paineenalaisten osien valmistuksen aikainen tarkastus, dokumentointi ja merkintä (2. painos) Tulitorvikattilat. Osa 5: Tarkastukset valmistuksen aikana, dokumentaatio ja paineenalaisten osien tunnusmerkintä EN 13480-5/FprA2 Revision of EN 13480-5 EN 13480-5/FprA3 Revision of EN 13480-5
17(17) Tuotestandardi Tuotespesifikaatio - laatuvaatimukset - tarkastuslaajuus - hylkäämisen aiheuttamat toimenpiteet 5817 Hitsiluokat -geometria - virheiden koot 17635 Hitsien rikkomaton aineenkoetus. Yleisohjeet metallisille materiaaleille - tarkastusmenetelmä - tarkastustekniikka - hyväksymisrajat - tarkastushenkilöstö Silmämääräinen Radiografia Tunkeumaneste Pyörrevirta Ultraääni Magneettijauhe 17637 5817 17636-1/2 10675-1/2 3452 23277 17643 Tuotestandardi 17640 11666 17638 23278 Sanasto EN 1330-10 Sanasto EN 1330-3 Sanasto 12706 Sanasto 12718 Sanasto EN 1330-4 Sanasto 12707 Yleisohjeet EN 13018 Yleisohjeet 5579 Yleisohjeet 3452-1 Yleisohjeet 15549 Yleisohjeet 16810 Yleisohjeet 9934-1 Laitteet EN 13927 Filmit 11699-1/2 Laitteet 3452-4 Laitteet 15548-1/3 Laitteet EN 12668-1/3 Laitteet 9934-3 Indikaattorit 19232-1/5 Tarkistuskappale 3452-3 Tarkastuskappale 7963 Tarkastusaineet 9934-2 NDT-henkilöstö 9712