SFS-STANDARDIT 2009. www.sesko.fi. Erikoisnumero tammikuu 2010. Ajankohtaista sähkö- ja elektroniikka-alan standardoinnista

Erikoisnumero tammikuu 2010 Ajankohtaista sähkö- ja elektroniikka-alan standardoinnista SESKOn alueelta julkaistut ja vahvistetut SFS-STANDARDIT 2009 SISÄLTÖ IEC-, EN- ja SFS-standardien valmistelu... 2 SFS-standardien valmistelu... 3 Johdanto... 3 SESKOn alueelta julkaistut ja vahvistetut standardit vuonna 2009 Suomenkielisinä julkaistut SFS-standardit, teknilliset raportit ja teknilliset spesifikaatiot... 4 Ruotsinkielisinä julkaistut SFS-standardit, teknilliset raportit ja teknilliset spesifikaatiot... 5 Luetteloimismenettelyllä vahvistetut SFS-standardit, teknilliset raportit ja teknilliset spesifikaatiot... 6 SESKOn valmistelemat SFS-käsikirjat... 24 SESKOn komiteat ja työryhmät... 25 SESKOn henkilöstö vastuualueineen... 26 SESKOn 45-vuotisjuhlaseminaari 31.3.2010 Yhteistyöllä parempia standardeja... 27 Standardien tilaaminen, yhteystietoja... 28 4 5 v u o t t a s ä h k ö a l a n standardeja 1 9 6 5 2 0 1 0 www.sesko.fi

IEC-, EN- ja SFS-standardien valmistelu. Rinnakkaismenettely. Ehdotus uudeksi työkohteeksi (NP Äänestys Ylläpitomenettely Valmisteluvaihe WG/PT/MT -ryhmien kansalliset jäsenet Lausuntokierros (CD) Lausunto tarvittaessa Äänestyskierros (CDV) Parallel UAP Kansallinen lausuntokierros Äänestys (IEC & CENELEC) Lausunto tarvittaessa (CENELEC) Muodollinen loppuäänestys (FDIS) Parallel FDIS Äänestykset ehdotuksiin (IEC & CENELEC) IEC-standardi EN-standardi SFS-EN-standardi SESKO-lehti Ajankohtaista sähköalan standardoinnista. ISSN 0783-2729. Sisältöä saa lainata lähteen mainiten. JULKAISIJA: SESKO ry, Särkiniementie 3, 00210, HELSINKI, p. (09) 696 391, faksi (09) 677 059, www.sesko.fi. TOIMITUS: Päätoimittaja Sinikka Hieta-Wilkman. Standardiluettelon toimittaja: Juha Vesa. Taitto: Tinni Karakorpi. Paino: Valopaino Oy TILAUKSET JA OSOITTEENMUUTOKSET: puh 09 696 3970, palaute@sesko.fi, vuosikerta 42, 4 + 1 nroa/2010.

SFS-standardien valmistelu Johdanto (Kansalliset toimenpiteet) Sähkö- ja elektroniikka-alalla standardit valmistellaan neljän pääperiaatteen mukaisesti: 1. Laaditaan maailmanlaajuinen IEC-standardi. IECstandardi tai HDasiakirja SFSstandardin uusiminen Kansallinen aloite 2. Laaditaan maailmanlaajuinen IEC-standardi, joka IEC/CENELEC-rinnakkaismenettelyllä vahvistetaan eurooppalaiseksi EN-standardiksi. Tämä on otettava kansallisesti käyttöön identtisenä SFS-EN-standardina. Standardin valmistelu SK-komiteassa Kansallinen lausuntokierros Standardin täsmentäminen SESKOn hyväksyntä SFS:n vahvistus 3. Laaditaan eurooppalainen EN-standardi, joka on otettava kansallisesti käyttöön identtisenä SFS-EN-standardina. 4. Laaditaan kansallinen SFS-standardi joko IEC-standardin pohjalta tai puhtaasti kansallisista lähtökohdista. EN-standardi on saatettava identtiseksi SFS-EN-standardiksi ja tämä voidaan tehdä yksinkertaisimmillaan luetteloimismenettelyä käyttämällä, jolloin kansallisesti ei julkaista mitään erillistä asiakirjaa, vaan ainoastaan asiasta ilmoitetaan SFS-tiedotuksessa. Lisäksi SFS-EN-standardin tunnus ja nimi ilmoitetaan SFS-standardiluettelossa. SFS-EN-standardi voidaan vahvistaa suomalaiseksi standardiksi myös julkaisemalla siitä suomenkielinen käännös. Standardin julkaiseminen (SFS) SFS-standardi SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

SESKOn valmistelemat standardit vuonna 2009 Tässä luettelossa esitetään SESKOn toimialueelta vuonna 2009 julkaistut SFS-standardit (suomen- tai ruotsinkieliset) sekä luetteloimalla vahvistetut SFS-standardit (englanninkieliset). SFS-tunnus Otsikko Vahvistus/ Suomenkielisinä julkaistut SFS-standardit, teknilliset raportit ja teknilliset spesifikaatiot SFS 2283 Uppoasennusrasiat. 78 mm jakorasia. Mitat SFS 2284 Uppoasennusrasiat. Kojerasia. Mitat SFS 2711 Sähkölämmittimet ja sähkölämmitysjärjestelmät. Käsitteet ja merkinnät 2009-03-09 SFS 3718 Uppoasennusrasiat. 70 mm jakorasia. Mitat SFS 3719 Uppoasennusrasiat. Kaksoiskojerasia. Mitat SFS 4884 Uppoasennusrasiat. Kojerasioiden kannet ja peitelevyt. Mitat SFS 5490 SFS 5798 Pienjännitevarokkeet. Ammattihenkilöiden käyttöön tarkoitettujen varokkeiden lisävaatimukset (pääasiassa teollisuuskäytön varokkeet). Kahvavarokkeet Kotitalouksiin ja vastaaviin käyttöihin tarkoitetut pistokytkimet. Suojajännitepistokytkimet (SELV) 2009-12-14 2009-12-14 SFS 5801 Voimakaapelit. Yleiset vaatimukset ja testaus alhaisessa lämpötilassa SFS 5855 Pienjännitevarokkeet. Maallikoiden käyttöön tarkoitettujen varokkeiden lisävaatimukset (pääasiassa kotitalouksiin ja vastaaviin käyttöihin tarkoitetut varokkeet). D-tyypin varokkeet 2009-12-14 SFS 6001 + A1 + A2 Suurjännitesähköasennukset 2009-05-25 SFS 6001/A2 Suurjännitesähköasennukset. Muutos 2 2009-05-25 SFS-EN 12665 Valo ja valaistus. Perustermit ja kriteerit valaistusvaatimusten määrittelemiseksi SFS-EN 15193 Rakennusten energiatehokkuus. Valaistuksen energiatehokkuus 2009-09-07 SFS-EN 50131-1 + A1 Hälytysjärjestelmät. Murto- ja ryöstöilmaisujärjestelmät. Osa 1: Järjestelmävaatimukset SFS-EN 50131-1/A1 Hälytysjärjestelmät. Murto- ja ryöstöilmaisujärjestelmät. Osa 1: Järjestelmävaatimukset SFS-CLC/TS 50131-7 Hälytysjärjestelmät. Murto- ja ryöstöilmaisujärjestelmät. Osa 7: Soveltamisohjeet 2009-08-17 2009-08-17 2009-03-30 SFS-EN 50174-1 SFS-EN 50174-2 SFS-CLC/TS 50398 SFS-EN 50408 Tietotekniikka. Kaapeloinnin asentaminen. Osa 1: Asennuksen spesifiointi ja laadunvarmistus Tietotekniikka. Kaapeloinnin asentaminen. Osa 2: Asennuksen suunnittelu ja asennuskäytännöt rakennusten sisätiloissa Hälytysjärjestelmät. Yhdistetyt ja integroidut hälytysjärjestelmät. Yleiset vaatimukset Kotitaloussähkölaitteiden ja vastaavien turvallisuus. Ajoneuvojen sisälämmittimien erityisvaatimukset 2009-09-07 2009-09-07 2009-05-11 2009-08-17 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

SFS-EN 50491-3 SFS-EN 60079-14 SFS-EN 60079-17 SFS-EN 60079-30-1 SFS-EN 60079-30-2 Yleiset vaatimukset kotien ja rakennusten elektroniikkajärjestelmille (HBES) sekä rakennusautomaatio- ja ohjausjärjestelmille (BACS). Osa 3: Sähköturvallisuusvaatimukset Räjähdysvaaralliset tilat. Osa 14: Sähköasennusten suunnittelu, laitevalinta ja asentaminen Räjähdysvaaralliset tilat. Osa 17: Sähköasennusten tarkastus ja kunnossapito Räjähdysvaaralliset tilat. Osa 30-1: Sähkösaatot. Yleiset ja testausvaatimukset Räjähdysvaaralliset tilat. Osa 30-2: Sähkösaatot. Soveltamisohjeita suunnitteluun, asentamiseen ja kunnossapitoon 2009-05-25 2009-08-17 SFS-EN 60204-1/A1 Koneturvallisuus. Koneiden sähkölaitteisto. Osa 1: Yleiset vaatimukset 2009-05-11 SFS-EN 60335-1/A13 SFS-EN 60376 SFS-EN 60480 Kotitaloussähkölaitteiden ja vastaavien turvallisuus. Osa 1: Yleiset vaatimukset Vaatimukset sähkölaitteissa käytettävälle tekniselle rikkiheksafluoridille (SF6) Ohjeet sähkölaitteista poistettavien rikkiheksafluoridin (SF6) tarkastamisesta ja käsittelemisestä sekä sen uudelleen käytöstä 2009-08-17 2009-11-23 2009-11-23 SFS-EN 60598-1 + A11 Valaisimet. Osa 1: Yleiset vaatimukset ja testit 2009-09-21 SFS-EN 60947-1 Pienjännitekytkinlaitteet. Osa 1: Pienkytkinlaitteet. Yleiset vaatimukset SFS-EN 61230 Jännitetyöt. Siirrettävät työmaadoitusvälineet tai työmaadoitus- ja oikosulkuvälineet SFS-EN 61242/A1 Asennustarvikkeet. Johtokelat kotitalouksiin ja vastaaviin käyttöihin 2009-03-09 SFS-EN 61340-5-1 CLC/TR 61340-5-2 Staattinen sähkö. Osa 5-1: Elektronisten komponenttien suojaaminen staattiselta sähköltä. Yleiset vaatimukset Staattinen sähkö. Osa 5-2: Elektronisten komponenttien suojaaminen staattiselta sähköltä. Käyttäjän opas 2009-05-11 2009-03-30 SFS-EN 62430 Sähkö- ja elektroniikkatuotteiden ympäristötietoinen suunnittelu 2009-09-07 IEC/TR 62513 SFS-EN 81346-2 Koneturvallisuus. Suuntaviivat tietoliikennejärjestelmien käyttämiseen turvallisuuteen liittyvissä sovelluksissa Teollisuuden järjestelmät, asennukset ja laitteet sekä teollisuustuotteet. Jäsentelyn periaatteet ja viitetunnukset. Osa 2: Kohteiden luokittelu ja luokkia vastaavat koodit 2009-05-25 2009-11-02 SFS-IEC 60050-411 + A1 Sähköteknillinen sanasto. Osa 411: Pyörivät koneet SFS-IEC 60050-461 Sähköteknillinen sanasto. Osa 461: Energiakaapelit SFS-IEC 60050-617 Sähköteknillinen sanasto. Osa 617: Organisaatio/sähkömarkkinat 2009-09-21 Ruotsinkielisinä julkaistut SFS-standardit, teknilliset raportit ja teknilliset spesifikaatiot SFS 6001 + A1 + A2 Högspänningselinstallationer 2009-05-25 SFS 6001/A2 Högspänningselinstallationer. Omändring A2 2009-05-25 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

Luetteloimismenettelyllä vahvistetut SFS-standardit, teknilliset raportit ja teknilliset spesifikaatiot SFS-CLC/TS 50131-2-7-1 Alarm systems. Intrusion and hold-up systems. Part 2-7-1: Intrusion detectors. Glass break detectors (acoustics) SFS-CLC/TS 50131-2-7-2 Alarm systems. Intrusion and hold-up systems. Part 2-7-2: Intrusion detectors. Glass break detectors (passive) SFS-CLC/TS 50131-2-7-3 Alarm systems. Intrusion and hold-up systems. Part 2-7-3: Intrusion detectors. Glass break detectors (active) SFS-EN 41003 SFS-EN 50083-8/A11 SFS-EN 50090-3-3 SFS-EN 50106 SFS-EN 50131-2-3 SFS-EN 50131-2-5 SFS-EN 50131-2-6 SFS-EN 50131-3 Particular safety requirements for equipment to be connected to telecommunication networks and/or a cable distribution system Cable networks for television signals, sound signals and interactive services. Part 8: Electromagnetic compatibility for networks Home and building electronic systems (HBES). Part 3-3: Aspects of applications. HBES interworking model and common HBES data types Safety of household and similar electrical appliances. Particular rules for routine tests referring to appliances under the scope of EN 60335-1 Alarm systems. Intrusion and hold-up systems. Part 2-3: Requirements for microwave detectors Alarm systems. Intrusion and hold-up systems. Part 2-5: Requirements for combined passive infrared and ultrasonic detectors Alarm systems. Intrusion and hold-up systems. Part 2-6: Opening contacts (magnetic) Alarm systems. Intrusion systems. Part 3: Control and indicating equipment SFS-EN 50131-4 Alarm systems. Intrusion and hold-up systems. Part 4: Warning devices SFS-EN 50131-5-3/A1 SFS-EN 50131-8 SFS-EN 50143 SFS-EN 50164-1 SFS-EN 50164-2 SFS-EN 50164-4 SFS-EN 50164-7 SFS-EN 50194-1 SFS-EN 50216-9 Alarm systems. Intrusion systems. Part 5-3: Requirements for interconnections equipment using radio frequency techniques Alarm systems. Intrusion and hold up-systems. Part 8: Security fog device/ systems Cables for signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 000 V but not exceeding 10 000 V Lightning Protection Components (LPC). Part 1: Requirements for connection components Lightning protection components (LPC). Part 2: Requirements for conductors and earth electrodes Lightning Protection Components (LPC). Part 4: Requirements for conductor fasteners Lightning Protection Components (LPC). Part 7: Requirements for earthing enhancing compounds Electrical apparatus for the detection of combustible gases in domestic premises. Part 1: Test methods and performance requirements Power transformer and reactor fittings. Part 9: Oil-to-water heat exchangers SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

SFS-EN 50216-10 Power transformer and reactor fittings. Part 10: Oil-to-air heat exchangers SFS-EN 50216-11 SFS-EN 50242 SFS-EN 50290-2-24/A1 SFS-EN 50304 SFS-EN 50342-3 SFS-EN 50377-2-2 SFS-EN 50402/A1 SFS-EN 50411-2 SFS-EN 50411-2-5 SFS-EN 50411-2-8 SFS-EN 50413 SFS-EN 50428/A2 SFS-EN 50465 Power transformer and reactor fittings. Part 11: Oil and winding temperature indicators Electric dishwashers for household use. Test methods for measuring the performance Communication cables. Part 2-24: Common design rules and construction. PE sheathing Electric ovens for household use. Methods for measuring the energy consumption Lead-acid starter batteries. Part 3: Terminal system for batteries with 36 V nominal voltage Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications. Part 2-2 : FC/APC 8 terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre, with full zirconia ferrule, category C Electrical apparatus for the detection and measurement of combustible or toxic gases or vapours or of oxygen. Requirements on the functional safety of fixed gas detection systems Fibre organisers and closures to be used in optical fibre communication systems. Product specifications. Part 2: General and guidance for optical fibre cable joint closures, protected microduct closures, and microduct connectors Fibre organisers and closures to be used in optical fibre communication systems. Product specifications. Part 2-5: Sealed closures for air blown fibre microduct, type 1, for category S & A Fibre organisers and closures to be used in optical fibre communication systems. Product specifications. Part 2-8: Microduct connectors, for air blown optical fibres, type 1 Basic standard on measurement and calculation procedures for human exposure to electric, magnetic and electromagnetic fields (0 Hz - 300 GHz) Switches for household and similar fixed electrical installations. Collateral standard. Switches and related accessories for use in home and building electronic systems (HBES) Gas appliances. Fuel cell gas heating appliance. Fuel cell gas heating appliance of nominal heat input inferior or equal to 70 kw SFS-EN 50483-1 Test requirements for low voltage aerial bundled cable accessories. Part 1: Generalities SFS-EN 50483-2 Test requirements for low voltage aerial bundled cable accessories. Part 2: Tension and suspension clamps for self supporting system SFS-EN 50483-3 Test requirements for low voltage aerial bundled cable accessories. Part 3: Tension and suspension clamps for neutral messenger system SFS-EN 50483-4 Test requirements for low voltage aerial bundled cable accessories. Part 4: Connectors SFS-EN 50483-5 Test requirements for low voltage aerial bundled cable accessories. Part 5: Electrical ageing test SFS-EN 50483-6 Test requirements for low voltage aerial bundled cable accessories. Part 6: Environmental testing SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

SFS-EN 50490 SFS-EN 50492 SFS-EN 50496 SFS-EN 50499 SFS-EN 50508 SFS-EN 50512 SFS-EN 50514 SFS-EN 55014-2/A2 SFS-EN 55016-1-1/A2 SFS-EN 55016-1-4/A1 SFS-EN 55025 SFS-EN 60034-4 SFS-EN 60061-1/A40 SFS-EN 60061-1/A41 SFS-EN 60061-2/A37 SFS-EN 60061-2/A38 SFS-EN 60061-3/A39 SFS-EN 60064/A11 Electrical installations for lighting and beaconing of aerodromes. Technical requirements for aeronautical ground lighting control and monitoring systems. Units for selective switching and monitoring of individual lamps Basic standard for the in-situ measurement of electromagnetic field strength related to human exposure in the vicinity of base stations Determination of workers` exposure to electromagnetic fields and assessment of risk at a broadcast site Procedure for the assessment of the exposure of workers to electromagnetic fields Multi-purpose insulating sticks for electrical operations on high voltage installations Electrical installations for lighting and beaconing of aerodromes. Advanced Visual Docking Guidance Systems (A-VDGS) Audio, video and information technology equipment. Routine electrical safety testing in production Electromagnetic compatibility. Requirements for household appliances, electric tools and similar apparatus. Part 2: Immunity. Product family standard Specification for radio disburbance and immunity measuring apparatus and methods. Part 1-1: Radio disturbance and immunity measuring apparatus. Measurement apparatus Specification for radio disturbance and immunity measuring apparatus and methods. Part 1-4: Radio disturbance and immunity measuring apparatus. Ancillary equipment. Radiated disturbances Vehicles, boats and internal combustion engines. Radio disturbance characteristics. Limits and methods of measurement for the protection of on-board receivers Rotating electrical machines. Part 4: Methods for determining synchronous machine quantities from tests Lamp caps and holders together with gauges for the control of interchangeability and safety. Part 1: Lamp caps Lamp caps and holders together with gauges for the control of interchangeability and safety. Part 1: Lamp caps Lamp caps and holders together with gauges for the control of interchangeability and safety. Part 2: Lampholders Lamp caps and holders together with gauges for the control of interchangeability and safety. Part 2: Lampholders Lamp caps and holders together with gauges for the control of interchangeability and safety. Part 3: Gauges Tungsten filament lamps for domestic and similar general lighting purposes. Performance requirements SFS-EN 60065/A11 Audio, video and similar electronic apparatus. Safety requirements SFS-EN 60068-2-2 Environmental testing. Part 2-2: Tests. Tests B: Dry heat SFS-EN 60068-2-20 Environmental testing. Part 2: Tests. Test T: Test methods for soldeability and resistance to soldering heat of devices with leads SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

SFS-EN 60068-2-27 Environmental testing. Part 2-27: Tests. Test Ea and guidance: Shock SFS-EN 60068-2-31 SFS-EN 60068-2-64 SFS-EN 60068-2-69 SFS-EN 60068-2-82 SFS-EN 60068-3-11 Environmental testing. Part 2-31: Tests. Test Ec: Rough Handling Shocks, primarily for equipment-type specimens Environmental testing. Part 2-64: Tests. Test Fh: Vibration, broadband random and guidance Environmental testing. Part 2-69: Tests. Test Te: Solderability testing of electronic components for surface mounting devices (SMD) by the wetting balance method Environmental testing. Part 2-82: Tests. Test Tx: Whisker test methods for electronic and electric components Environmental testing. Part 3-11: Supporting documentation and guidance. Calculation of the uncertainty of conditions in climatic test chambers SFS-EN 60079-6 Explosive atmospheres. Part 6: Equipment protection by oil immersion o SFS-EN 60079-27 SFS-EN 60099-4/A2 SFS-EN 60127-4/A1 Explosive atmospheres. Part 27: Fieldbus intrinsically safe concept (FISCO) Surge arresters. Part 4: Metal-oxide surge arresters without gaps for a.c. systems Miniature fuses. Part 4: Universal modular fuse-links (UMF). Through-hole and surface mount types SFS-EN 60137 Insulated bushings for alternating voltages above 1000 V SFS-EN 60238/A1 Edison screw lampholders SFS-EN 60255-22-3 Measuring relays and protection equipment. Part 22-3: Electrical disturbance tests. Radiated electromagnetic field immunity SFS-EN 60264-1/A1 Packaging of winding wires. Part 1: Containers for round winding wires SFS-EN 60286-2 Packaging of components for automatic handling. Part 2: Packaging of components with unidirectional leads on continuous tapes SFS-EN 60286-5/A1 Packaging of components for automatic handling. Part 5: Matrix trays SFS-EN 60297-3-100 SFS-EN 60297-3-105 SFS-EN 60300-3-16 SFS-EN 60317-0-3 SFS-EN 60318-6 SFS-EN 60335-2-5/A2 SFS-EN 60335-2-5/A11 Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482,6 mm (19 in) series. Part 3-100: Basic dimensions of front panels, subracks, chassis, racks and cabinets Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482,6 mm (19 in) series. Part 3-105: Dimensions and design aspects for 1U high chassis Dependability management. Part 3-16: Application guide. Guidelines for the specification of maintenance support services Specifications for particular types of winding wires. Part 0: General requirements. Section 3: Enamelled round aluminium wire Electroacoustics. Simulators of human head and ear. Part 6: Mechanical coupler for the measurement of bone vibrators Household and similar electrical appliances. Safety. Part 2-5: Particular requirements for dishwashers Household and similar electrical appliances. Safety. Part 2-5: Particular requirements for dishwashers SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

SFS-EN 60335-2-8/A2 SFS-EN 60335-2-11/A11 SFS-EN 60335-2-14/A1 SFS-EN 60335-2-15/A2 SFS-EN 60335-2-17/A2 SFS-EN 60335-2-21/A2 SFS-EN 60335-2-27/A1 SFS-EN 60335-2-27/A2 SFS-EN 60335-2-31/A2 SFS-EN 60335-2-32/A1 SFS-EN 60335-2-34/A2 SFS-EN 60335-2-39/A2 SFS-EN 60335-2-40/A2 SFS-EN 60335-2-42/A1 SFS-EN 60335-2-43/A2 SFS-EN 60335-2-49/A1 SFS-EN 60335-2-54 SFS-EN 60335-2-60/A2 SFS-EN 60335-2-61/A2 Household and similar electrical appliances. Safety. Part 2-8: Particular requirements for shavers, hair clippers and similar appliances Household and similar electrical appliances. Safety. Part 2-11: Particular requirements for tumble dryers Household and similar electrical appliances. Safety. Part 2 14: Particular requirements for kitchen machines Household and similar electrical appliances. Safety. Part 2-15: Particular requirements for appliances for heating liquids Household and similar electrical appliances. Safety. Part 2-17: Particular requirements for blankets, pads, clothing and similar flexible heating appliances Household and similar electrical appliances. Safety. Part 2-21: Particular requirements for storage water heaters Household and similar electrical appliances. Safety. Part 2-27: Particular requirements for appliances for skin exposure to ultraviolet and infrared radiation Household and similar electrical appliances. Safety. Part 2-27: Particular requirements for appliances for skin exposure to ultraviolet and infrared radiation Household and similar electrical appliances. Safety. Part 2 31: Particular requirements for range hoods and other cooking fume extractors Household and similar electrical appliances. Safety. Part 2-32: Particular requirements for massage appliances Household and similar electrical appliances. Part 2-34: Safety. Particular requirements for motor-compressors Household and similar electrical appliances. Safety. Part 2-39: Particular requirements for commercial electric multi-purpose cooking pans Household and similar electrical appliances. Safety. Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers Household and similar electrical appliances. Safety. Part 2-42: Particular requirements for commercial electric forced convection ovens, steam cookers and steam-convection ovens Household and similar electrical appliances. Safety. Part 2-43: Particular requirements for clothes dryers and towel rails Household and similar electrical appliances. Safety. Part 2-49: Particular requirements for commercial electric appliances for keeping food and crockery warm Household and similar electrical appliances. Safety. Part 2-54: Particular requirements for surface-cleaning appliances for household use employing liquids or steam Household and similar electrical appliances. Safety. Part 2: Particular requirements for whirlpool baths and whirlpool spas Household and similar electrical appliances. Safety. Part 2-61: Particular requirements for thermal-storage room heaters SFS-EN 60335-2-75/A1 Household and similar electrical appliances. Safety. Part 2-75: Particular requirements for commercial dispensing appliances and vending machines 10 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

SFS-EN 60335-2-80/A2 SFS-EN 60335-2-96/A2 SFS-EN 60335-2-97/A11 SFS-EN 60335-2-98/A2 SFS-EN 60350 SFS-EN 60352-5 Household and similar electrical appliances. Safety. Part 2-80: Particular requirements for fans Household and similar electrical appliances. Safety. Part 2-96: Particular requirements for flexible sheet heating elements for room heating Household and similar electrical appliances. Safety. Part 2-97: Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment Household and similar electrical appliances. Safety. Part 2-98: Particular requirements for humidifiers Electric cooking ranges, hobs, ovens and grills for household use. Methods for measuring performance Solderless connections. Part 5: Press-in connections. General requirements, test methods and practical guidance SFS-EN 60357/A2 Tungsten halogen lamps (non-vehicle). Performance specifications SFS-EN 60399/A1 Barrel thread for lampholders with shade holder ring SFS-EN 60400 Lampholders for turbular fluorescent lamps and starterholders SFS-EN 60404-4/A2 SFS-EN 60404-8-6 SFS-EN 60424-5 Magnetic materials. Part 4: Methods of measurement of d.c. magnetic properties of magnetically soft materials Magnetic materials. Part 8-6: Specifications for individual materials. Soft magnetic metallic materials Ferrite cores. Guide on the limits of surface irregularities. Part 5: Planarcores SFS-EN 60512-15-1 Connectors for electronic equipment. Tests and measurements. Part 15-1: Connector tests (mechanical). Test 15a: Contact retention in insert SFS-EN 60512-15-2 Connectors for electronic equipment. Tests and measurements. Part 15-2: Connector tests (mechanical). Test 15b: Insert retention in housing (axial) SFS-EN 60512-15-3 Connectors for electronic equipment. Tests and measurements. Part 15-3: Connector tests (mechanical). Test 15c: Insert retention in housing (torsional) SFS-EN 60512-15-4 Connectors for electronic equipment. Tests and measurements. Part 15-4: Connector tests (mechanical). Test 15d: Contact insertion, release and extraction force SFS-EN 60512-15-5 Connectors for electronic equipment. Tests and measurements. Part 15-5: Connector tests (mechanical). Test 15e: Contact retention in insert, cable nutation SFS-EN 60512-15-6 Connectors for electronic equipment. Tests and measurements. Part 15-5: Connector tests (mechanical). Test 15f: Effectiveness of connector coupling devices SFS-EN 60512-15-7 Connectors for electronic equipment. Tests and measurements. Part 15-7: Connector tests (mechanical). Test 15g: Robustness of protective cover attachment SFS-EN 60512-16-1 Connectors for electronic equipment. Tests and measurements. Part 16-1: Mechanical tests on contacts and terminations. Test 16a: Probe damage SFS-EN 60512-16-2 Connectors for electronic equipment. Tests and measurements. Part 16-2: Mechanical tests on contacts and terminations. Test 16b: Restricted entry SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009 11

SFS-EN 60512-16-3 Connectors for electronic equipment. Tests and measurements. Part 16-3: Mechanical tests on contacts and terminations. Test 16c: Contact-bending strength SFS-EN 60512-16-4 Connectors for electronic equipment. Tests and measurements. Part 16-4: Mechanical tests on contacts and terminations. Test 16d: Tensile strength (crimped connections) SFS-EN 60512-16-5 Connectors for electronic equipment - Tests and measurements - Part 16-5: Mechanical tests on contacts and terminations - Test 16e: Gauge retention force (resilient contacts) SFS-EN 60512-16-6 Connectors for electronic equipment. Tests and measurements. Part 16-6: Mechanical tests on contacts and terminations. Test 16f: Robustness of terminations SFS-EN 60512-16-7 Connectors for electronic equipment. Tests and measurements. Part 16-7: Mechanical tests on contacts and terminations. Test 16g: Measurement of contact deformation after crimping SFS-EN 60512-16-8 Connectors for electronic equipment. Tests and measurements. Part 16-8: Mechanical tests on connections and terminations. Test 16h: Insulating grip effectiveness (crimped contacts) SFS-EN 60512-16-9 Connectors for electronic equipment. Tests and measurements. Part 16-9: Mechanical tests on contacts and terminations. Test 16i: Grounding contact spring holding force SFS-EN 60512-16-11 Connectors for electronic equipment. Tests and measurements. Part 16-11: Mechanical tests on contacts and terminations. Test 16k: Stripping force, solderless wrapped connections SFS-EN 60512-16-13 Connectors for electronic equipment. Tests and measurements. Part 16-13: Mechanical tests on contacts and terminations. Test 16m: Unwrapping, solderless wrapped connections SFS-EN 60512-16-14 Connectors for electronic equipment. Tests and measurements. Part 16-14: Mechanical tests on contacts and terminations. Test 16n: Bending strength, fixed male tabs SFS-EN 60512-16-16 Connectors for electronic equipment. Tests and measurements. Part 16-16: Mechanical tests on contacts and terminations. Test 16p: Torsional strength, fixed male tabs SFS-EN 60512-16-17 Connectors for electronic equipment. Tests and measurements. Part 16-17: Mechanical tests on contacts and terminations. Test 16q: Tensile and compressive strength, fixed male tabs SFS-EN 60512-16-18 Connectors for electronic equipment. Tests and measurements. Part 16-18: Mechanical tests on contacts and terminations. Test 16r: Deflection of contacts, simulation SFS-EN 60512-25-9 Connectors for electrical equipment. Tests and measurements. Part 25-9: Signal integrity tests. Test 25i: Alien crosstalk SFS-EN 60512-26-100 SFS-EN 60519-7 SFS-EN 60519-21 Connectors for electronic equipment. Tests and measurements. Part 26-100: Measurement setup, test and reference arrangements and measurements for connectors according to IEC 60603-7. Tests 26a to 26g Safety in electroheat installations. Part 7: Particular requirements for installations with electron guns Safety in electroheat installations. Part 21: Particular requirements for resistance heating equipment. Heating and melting glass equipment 12 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

SFS-EN 60534-2-4 SFS-EN 60598-2-14 SFS-EN 60601-2-2 SFS-EN 60601-2-19 SFS-EN 60601-2-21 SFS-EN 60601-2-29 SFS-EN 60601-2-44 SFS-EN 60601-2-50 SFS-EN 60626-3 SFS-EN 60641-3-1 SFS-EN 60689 SFS-EN 60695-1-30 SFS-EN 60700-1/A2 Industrial-process control valves. Part 2-4: Flow capacity. Inherent flow characteristics and rangeability Luminaires. Part 2-14: Particular requirements. Luminaires for cold cathode tubular discharge lamps (neon tubes) and similar equipment Medical electrical equipment. Part 2-2: Particular requirements for the basic safety and essential performance of high frequency surgical equipment and high frequency surgical accessories Medical electrical equipment. Part 2-19: Particular requirements for the basic safety and essential performance of infant incubators Medical electrical equipment. Part 2: Particular requirements for the basic safety and essential performance of infant radiant warmers Medical electrical equipment. Part 2-29: Particular requirements for the basic safety and essential performance of radiotherapy simulators Medical electrical equipment. Part 2-44: Particular requirements for the basic safety and essential performance of X-ray equipment for computed tomography Medical electrical equipment. Part 2-50: Particular requirements for the basic safety and essential performance of infant phototherapy equipment Combined flexible materials for electrical insulation. Part 3: Specifications for individual materials Pressboard and presspaper for electrical purposes. Part 3: Specifications for individual materials. Sheet 1: Requirements for pressboard, types B.0.1, B.0.3, B.2.1, B.2.3, B.3.1, B.3.3, B.4.1, B.4.3, B.5.1, B.5.3 and B.6.1 Measurement and test methods for tuning fork quartz crystal units in the range from 10 khz to 200 khz and standard values Fire hazard testing. Part 1-30: Guidance for assessing the fire hazard of electrotechnical products. Preselection testing process. General guidelines Thyristor valves for high voltage direct current (HVDC) power transmission. Part 1: Electrical testing SFS-EN 60703 Test methods for electroheating installations with electron guns SFS-EN 60704-2-13/A2 SFS-EN 60728-1 SFS-EN 60728-4 SFS-EN 60728-5 Household and similar electrical appliances. Test code for the determination of airborne acoustical noise. Part 2-13: Particular requirements for range hoods Cable networks for television signals, sound signals and interactive services. Part 1: System performance of forward paths Cable networks for television signals, sound signals and interactive services. Part 4: Passive wideband equipment for coaxial cable networks Cabled networks for television signals, sound signals and interactive services. Part 5: Headend equipment SFS-EN 60730-2-6 Automatic electrical controls for household and similar use. Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements SFS-EN 60730-2-14/A2 Automatic electrical controls for household and similar use. Part 2-14: Particular requirements for electric actuators SFS-EN 60745-2-1/A1 Hand-held motor-operated electric tools. Safety. Part 2-1: Particular requirements for drills and impact drills SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009 13

SFS-EN 60745-2-2/A1 SFS-EN 60745-2-4/A1 SFS-EN 60745-2-6/A2 SFS-EN 60745-2-8/A1 SFS-EN 60745-2-11/A1 SFS-EN 60745-2-12/A1 SFS-EN 60745-2-20/A1 Hand-held motor-operated electric tools. Safety. Part 2-2: Particular requirements for screwdrivers and impact wrenches Hand-held motor-operated electric tools. Safety. Part 2-4: Particular requirements for sanders and polishers other than disk type Hand-held motor-operated electric tools. Safety. Part 2-6: Particular requirements for hammers Hand-held motor-operated electric tools. Safety. Part 2-8: Particular requirements for shears and nibblers Hand-held motor-operated electric tools. Safety. Part 2-11: Particular requirements for reciprocating saws (jig and sabre saws) Hand-held motor operated electric tools. Safety. Part 2-12: Particular requirements for concrete vibrators Hand-held motor-operated electric tools. Safety. Part 2-20: Particular requirements for band saws SFS-EN 60749-37 Semiconductor devices. Mechanical and climatic test methods. Part 37: Board level drop test method using an accelerometer SFS-EN 60749-38 Semiconductor devices. Mechanical and climatic test methods. Part 38: Soft error test method for semiconductor devices with memory SFS-EN 60751 Industrial platinum resistance thermometers and platinum temperature sensors SFS-EN 60758 Synthetic quartz crystal. Specifications and guide for use SFS-EN 60793-1-1 SFS-EN 60793-1-47 SFS-EN 60793-2-20 SFS-EN 60793-2-30 SFS-EN 60793-2-50 SFS-EN 60794-2-30 SFS-EN 60794-2-41 SFS-EN 60794-3-10 SFS-EN 60794-3-20 SFS-EN 60794-3-30 SFS-EN 60794-3-40 Optical fibres. Part 1-1: Measurement methods and test procedures. General and guidance Optical fibres. Part 1 47: Measurement methods and test procedures. Macrobending loss Optical fibres. Part 2-20: Product specifications. Sectional specification for category A2 multimode fibres Optical fibres. Part 2-30: Product specifications. Sectional specification for category A3 multimode fibres Optical fibres. Part 2-50: Product specifications. Sectional specification for class B single-mode fibres Optical fibre cables. Part 2-30: Indoor cables. Family specification for ribbon cables Optical fibre cables. Part 2-41: Indoor cables. Product specification for simplex and duplex buffered A4 fibres Optical fibre cables. Part 3-10: Outdoor cables. Family specification for duct, directly buried and lashed aerial optical telecommunication cables Optical fibre cables. Part 3-20: Outdoor cables. Family specification for self-supporting aerial telecommunication cables Optical fibres cables. Part 3-30: Outdoor cables. Family specification for optical telecommunication cables for lakes and river crossings Optical fibre cables. Part 3-40: Outdoor optical fibre cables. Family specification for sewer cables and conduits for installation by blowing and/ or pulling in non-man accessible storm and sanitary sewers 14 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

SFS-EN 60794-3-50 SFS-EN 60794-3-60 SFS-EN 60809/A4 Optical fibre cables. Part 3-50: Outdoor cables. Family specification for gas pipe cables and subducts for installation by blowing and/or pulling/ dragging in gas pipes Optical fibre cables. Part 3-60: Outdoor cables. Family specification for drinking water pipe cables and subducts for installation by blowing and/or pulling/dragging/floating in drinking water pipes Lamps for road vehicles. Dimensional, electrical and luminous requirements SFS-EN 60810/A1 Lamps for road vehicles. Performance requirements SFS-EN 60825-4/A1 Safety of laser products. Part 4: Laser guards SFS-EN 60838-1/A1 Miscellaneous lampholders. Part 1: General requirements and tests SFS-EN 60851-3 Winding wires. Test methods. Part 3: Mechanical properties SFS-EN 60851-5 Winding wires. Test methods. Part 5: Electrical properties SFS-EN 60898-1/A12 SFS-EN 60904-3 SFS-EN 60947-3 SFS-EN 60947-5-1/A1 SFS-EN 60950-22/A11 Electrical accessories. Circuit breakers for overcurrent protection for household and similar installations. Part 1: Circuit-breakers for a.c. operation Photovoltaic devices. Part 3: Measurement principles for terrestrial photovoltaic (PV) solar devices with reference spectral irradiance data Low-voltage switchgear and controlgear. Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units Low-voltage switchgear and controlgear. Part 5-1: Control circuit devices and switching elements. Electromechanical control circuit devices Information technology equipment. Safety. Part 22: Equipment installed outdoor SFS-EN 60958-1 Digital audio interface. Part 1: General SFS-EN 60958-4/A1 Digital audio interface. Part 4: Professional applications SFS-EN 60966-3 SFS-EN 60966-3-1 SFS-EN 60974-8 SFS-EN 61000-3-3 SFS-EN 61000-4-3/A1 SFS-EN 61000-4-30 SFS-EN 61008-1/A12 Radio frequency and coaxial cable assemblies. Part 3: Sectional specification for semi-flexible coaxial cable assemblies Radio frequency and coaxial cable assemblies. Part 3-1: Blank detail specification for semi-flexible coaxial cable assemblies Arc welding equipment. Part 8: Gas consoles for welding and plasma cutting systems Electromagnetic compatibility (EMC). Part 3-3: Limits. Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current 16 A per phase and not subject to conditional connection Electromagnetic compatibility (EMC). Part 4-3: Testing and measurement techniques. Radiated, radio-frequency, electromagnetic field immunity test Electromagnetic compatibility (EMC). Part 4-30: Testing and measurement techniques. Power quality measurement methods Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB s). Part 1: General rules SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009 15

SFS-EN 61009-1/A12 SFS-EN 61009-1/A13 SFS-EN 61023 Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO s). Part 1: General rules Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO s). Part 1: General rules Maritime navigation and radiocommunication equipment and systems. Marine speed and distance measuring equipment (SDME). Performance requirements, methods of testing and required test results SFS-EN 61039 Classification of insulating liquids SFS-EN 61051-1 Varistors for use in electronic equipment. Part 1: Generic specification SFS-EN 61073-1 Fibre optic interconnecting devices and passive components. Mechanical splices and fusion splice protectors for optical fibres and cables. Part 1: Generic specification SFS-EN 61076-2-101 Connectors for electronic equipment. Product requirements. Part 2-101: Circular connectors. Detail specification for M12 connectors with screwlocking SFS-EN 61076-2-104 Connectors for electronic equipment. Product requirements. Part 2-104: Detail specification for circular connectors with M8 screw-locking or snaplocking SFS-EN 61076-2-105 Connectors for electronic equipment. Product requirements. Part 2-105: Circular connectors. Detail specification for M5 connectors with screwlocking SFS-EN 61076-3 Connectors for electronic equipment. Part 3: Rectangular connectors. Sectional specification SFS-EN 61076-3-001 Connectors for electronic equipment. Product requirements. Part 3: Rectangular connectors. Blank detail specification SFS-EN 61076-3-110 Connectors for electronic equipment. Product requirements. Part 3-110: Rectangular connectors. Detail specification for shielded, free and fixed connectors for data transmission with frequencies up to 1000 MHz SFS-EN 61076-3-116 Connectors for electronic equipment. Product requirements. Part 3-116: Rectangular connectors. Detail specification for protective housings for use with 8-way shielded and unshielded connectors for frequencies up to 600 MHz for industrial environments incorporating the IEC 60603-7 series interface. Variant 13 related to IEC 61076-3-106. Locking lever SFS-EN 61095 Electromechanical contactors for household and similar purposes SFS-EN 61097-1 SFS-EN 61109 SFS-EN 61162-3 SFS-EN 61174 Global maritime distress and safety system (GMDSS). Part 1: Radar transponder. Marine search and rescue (SART). Operational and performance requirements, methods of testing and required test results Insulators for overhead lines. Composite suspension and tension insulators for a.c. systems with a nominal voltage greater than 1000 V. Definitions, test methods and acceptance criteria Maritime navigation and radiocommunication equipment and systems. Digital interfaces. Part 3: Serial data instrument network Maritime navigation and radiocommunication equipment and systems. Electronic chart display and information system (ECDIS). Operational and performance requirements, methods of testing and required test results SFS-EN 61184 Bayonet lampholders 16 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

SFS-EN 61188-5-3 Printed boards and printed board assemblies. Design and use. Part 5-3: Attachment (land/joint) considerations. Components with gull-wing leads on two sides SFS-EN 61188-5-4 Printed boards and printed board assemblies. Design and use. Part 5-4: Attachment (land/joint) considerations. Components with J leads on two sides SFS-EN 61188-5-5 Printed boards and printed board assemblies. Design and use. Part 5-5: Attachment (land/joint) considerations. Components with gull-wing leads on four sides SFS-EN 61190-1-2 SFS-EN 61190-1-3 Attachment materials for electronic assembly. Part 1-2: Requirements for solder pastes for high-quality interconnections in electronics assembly Attachment materials for electronic assembly. Part 1-3: Requirements for electronic grade solder alloys and fluxed and non-fluxed solid solder for electronic soldering applications SFS-EN 61192-5 Workmanship requirements for soldered electronic assemblies. Part 5: Rework, modification and repair of soldered electronic assemblies SFS-EN 61193-2 SFS-EN 61249-2-35 SFS-EN 61249-2-36 Quality assessment systems. Part 2: Selection and use of sampling plans for inspection of electronic components and packages Materials for printed boards and other interconnecting structures. Part 2-35: Reinforced base materials; clad and unclad. Modified epoxide woven E-glass laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly Materials for printed boards and other interconnecting structures. Part 2-36: Reinforced base materials; clad and unclad. Epoxide woven E-glass laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly SFS-EN 61249-2-37 Materials for printed boards and other interconnecting structures. Part 2-37: Reinforced base materials; clad and unclad. Modified non-halogenated epoxide woven E-glass laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly SFS-EN 61249-2-38 Materials for printed boards and other interconnecting structures. Part 2-38: Reinforced base materials; clad and unclad. Non-halogenated epoxide woven E-glass laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly SFS-EN 61274-1-1 Adaptors for fibre optic connectors. Part 1-1: Blank detail specification SFS-EN 61280-2-2 Fibre optic communication subsystem test procedures. Part 2-2: Digital systems. Optical eye pattern, waveform and extinction ratio measurement SFS-EN 61280-2-9 Fibre optic communication subsystem basic test procedures. Part 2-9: Digital systems. Optical signal-to-noise ratio measurement for dense wavelength-division multiplexed systems SFS-EN 61290-3 Optical amplifiers. Test methods. Part 3: Noise figure parameters SFS-EN 61290-3-2 SFS-EN 61290-10-1 SFS-EN 61290-11-1 Optical amplifiers. Test methods. Part 3-2: Noise figure parameters. Electrical spectrum analyzer method Optical amplifiers. Test methods. Part 10-1: Multichannel parameters. Pulse method using an optical switch and optical spectrum analyzer Optical amplifiers. Test methods. Part 11-1: Polarization mode dispersion parameter. Jones matrix eigenanalysis (JME) SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009 17

SFS-EN 61291-4 Optical amplifiers. Part 4: Multichannel applications. Performance specification template SFS-EN 61291-6-1 Optical amplifiers. Part 6-1: Interfaces. Command set SFS-EN 61298-1 SFS-EN 61298-2 SFS-EN 61298-3 SFS-EN 61298-4 SFS-EN 61300-2-2 SFS-EN 61300-2-44 SFS-EN 61300-2-48 Process measurement and control devices. General methods and procedures for evaluating performance. Part 1: General considerations Process measurement and control devices. General methods and procedures for evaluating performance. Part 2: Tests under reference conditions Process measurement and control devices. General methods and procedures for evaluating performance. Part 3: Tests for the effects of influence quantities Process measurement and control devices. General methods and procedures for evaluating performance. Part 4: Evaluation report content Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-2: Tests. Mating durability Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-44: Tests. Flexing of the strain relief of fibre optic devices Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-48: Tests. Temperature-humidity cycling SFS-EN 61300-3-2 SFS-EN 61300-3-3 SFS-EN 61300-3-6 Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-2: Examinations and measurements. Polarization dependence loss in a single-mode fibre optic device Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-3: Examinations and measurements. Active monitoring of changes in attenuation and return loss Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-6: Examinations and measurements. Return loss SFS-EN 61300-3-34 SFS-EN 61300-3-43 SFS-EN 61314-1 SFS-EN 61347-2-10/A1 SFS-EN 61400-21 SFS-EN 61400-25-4 Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-34: Examinations and measurements. Attenuation of random mated connectors Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-43: Examinations and measurements. Mode transfer function measurement for fibre optic sources Fibre optic interconnecting devices and passive components. Fibre optic fan-outs. Part 1: Generic specification Lamp controlgear. Part 2-10: Particular requirements for electronic invertors and convectors for high-frequency operation of cold start tubular discharge lamps (neon tubes) Wind turbines. Part 21: Measurement and assessment of power quality characteristics of grid connected wind turbines Wind turbines. Part 25-4: Communications for monitoring and control of wind power plants. Mapping to communication profile 18 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009

SFS-EN 61467 SFS-EN 61477 Insulators for overhead lines. Insulator strings and sets for lines with a nominal voltage greater than 1000 V. AC power arc tests Live working. Minimum requirements for the utilization of tools, devices and equipment SFS-EN 61496-1/A1 Safety of machinery. Electro-sensitive protective equipment. Part 1: General requirements and tests SFS-EN 61512-3 Batch control. Part 3: General and site recipe models and representation SFS-EN 61534-22 SFS-EN 61557-9 SFS-EN 61557-11 SFS-EN 61558-1/A1 SFS-EN 61558-2-4 SFS-EN 61558-2-13 SFS-EN 61606-3 SFS-EN 61643-21 SFS-EN 61646 Powertrack systems. Part 22: Particular requirements for powertrack systems intended for on floor or under floor installation Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures. Part 9: Equipment for insulation fault location in IT systems Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Equipment for testing, measuring or monitoring of protective measures. Part 11: Effectiveness of residual current monitors (RCMs) type A and type B in TT, TN and IT systems Safety of power transformers, power supplies, reactors and similar products. Part 1: General requirements and tests Safety of power transformers, power supply units and similar products for supply voltages up to 1 100 V. 2-4: Particular requirements and tests for isolating transformers and power supply units incorporating isolating transformers Safety of transformers, reactors, power supply units and similar products for voltages up to 1 100 V. Part 2-13: Particular requirements and tests for auto transformers and power supply units incorporating auto transformers Audio and audiovisual equipment. Digital audio parts. Basic measurements methods of audio characteristics. Part 3: Professional use Low voltage surge protective devices. Part 21: Surge protective devices connected to telecommunications and signalling networks. Performance requirements and testing methods Thin-film terrestrial phovoltaic (PV) modules. Design qualification and type approval SFS-EN 61649 Weilbull analysis SFS-EN 61676/A1 SFS-EN 61730-1 SFS-EN 61730-2 SFS-EN 61753-031-3 SFS-EN 61753-101-3 Medical electrical equipment. Dosimetric instruments used for non-invasive measurement of X-ray tube voltage in diagnostic radiology Photovoltaic (PV) module safety qualification. Part 1: Requirements for construction Photovoltaic (PV) module safety qualification. Part 2: Requirements for testing Fibre optic interconnecting devices and passive components performance standard. Part 031-3: Non-connectorized single mode 1xN and 2xN non-wavelength-selective branching devices (NWBD) for category U. Uncontrolled environment Fibre optic interconnecting devices and passive components performance standard. Part 101-3: Fibre management systems for category U. Uncontrolled environment SFS-EN 61754-25 Fibre optic connector interfaces. Part 25: Type RAO connector family SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2009 19