Ajankohtaista sähköteknisen alan standardoinnista SESKOn alueelta julkaistut SFS-STANDARDIT 2017 SISÄLTÖ

Transkriptio

1 Ajankohtaista sähköteknisen alan standardoinnista SESKOn alueelta julkaistut SFS-STANDARDIT 2017 SISÄLTÖ Johdanto IEC-, EN- ja SFS-EN-standardien valmistelu (rinnakaismenettely), EN- ja SFS-standardien valmistelu (ilman rinnakkaismenettelyä), SFS-standardien valmistelu Suomalaiset SFS-standardit ja suomenkielisinä julkaistut SFS-EN-standardit Ruotsinkielisenä julkaistu SFS-standardi Englanninkielisinä julkaistut SFS-EN-standardit SFS-käsikirjat

2 Johdanto Nykyisin vahvistettavista kansallisista SFS-standardeista on suurin osa SFS-EN-standardeja, sillä ENstandardit on saatettava identtisiksi SFS-EN-standardeiksi. Suunnilleen 85 % sähköalan EN-standardeista perustuu IEC-standardeihin ja tarvittaessa niitä on täydennetty yhteiseurooppalaisilla muutoksilla. IECstandardeja ja muita IEC-julkaisuja on voimassa noin 7300 kpl. Jos IEC ei ole kiinnostunut laatimaan kansainvälistä standardia tietyltä alueelta, niin CENELEC laatii tällöin puhtaasti eurooppalaisen EN-standardin (home grown). Näitä on noin 15 % kaikista eurooppalaisista standardeista. Lisäksi CENELEC laatii HD-harmonisointiasiakirjoja, kun ei ole mahdollista tehdä ENstandardia esimerkiksi kansallisten käytäntöjen vuoksi. HD-harmonisointiasiakirjaa ei ole pakko vahvistaa kansalliseksi standardiksi, mutta siitä voidaan vahvistaa osia suomalaiseksi standardiksi sisältöä muuttamatta. Näin on tehty esimerkiksi suomalaisia energiakaapelistandardeja. Kansallisia SFS-standardeja laaditaan enää hyvin harvoin ja niitä tehdään lähinnä sanastoista, sähköasennuksista, energiakaapeleista ja eräistä muista vastaavista aiheista, joissa eri mailla on erilaisia käytäntöjä. Tällöinkin SFS-standardin esikuvana on joko IEC-standardi tai HD-harmonisointiasiakirja. Nykyisin kaikki sähköalan eurooppalaiset EN-standardit julkaistaan englanninkielisinä SFS-EN-standardeina. Osa standardeista käännetään myöhemmin ja yleensä tämä standardi sisältää myös alkuperäisen englanninkielisen tekstin. Tällainen standardi ei kumoa aiemmin julkaistua englanninkielistä SFS-ENstandardia. Näin ollen eräistä SFS-EN-standardeista on olemassa sekä englanninkielinen versio että kaksikielinen versio, joka sisältää myös suomenkielisen käännöksen.tiedot kaikista SFS-, SFS-EN- ja IECstandardeista sekä SFS-käsikirjoista löytyvät SFS-kaupasta ja niitä voi tilata Suomen Standardisoimisliitto SFS ry:n myyntipalvelusta. IEC:n verkkokaupasta voi hankkia suoraan yksittäisiä IECstandardeja ja standardikokoelmia. SESKO neuvoo suomalaisia sähköalan standardien käytössä (asiakaspalvelu@sesko.fi, p ). 2

3 3 SESKOn alueelta julkaistut SFS-standardit 2017

4 Suomalaiset SFS-standardit ja suomenkielisinä julkaistut SFS-EN-standardit Vahvistus/julkaisupäivämäärä SFS ,6/1 kv kaapelit. Riippukierrekaapeli AMKA SFS 5636 PEX-eristeiset 10, 20 ja 30 kv Al- ja Cu-voimakaapelit. Rakenne ja testaus SFS 5702 PEX-eristeiset 64/110 kv voimakaapelit ja niiden varusteet. Rakenne ja testaus SFS 5805 Pistokytkimet. Sanasto SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS Pienjännitesähköasennukset. Osa 1: Perusperiaatteet, yleisten ominaisuuksien määrittely ja määritelmät Pienjännitesähköasennukset. Osa 4-41: Suojausmenetelmät. Suojaus sähköiskulta Pienjännitesähköasennukset. Osa 4-42: Suojausmenetelmät. Suojaus lämmön vaikutuksilta Pienjännitesähköasennukset. Osa 4-43: Suojausmenetelmät. Ylivirtasuojaus Pienjännitesähköasennukset. Osa 4-44: Suojausmenetelmät. Suojaus jännitehäiriöiltä ja sähkömagneettisilta häiriöiltä Pienjännitesähköasennukset. Osa 4-46: Suojausmenetelmät. Erottaminen ja kytkentä Pienjännitesähköasennukset. Osa 5-51: Sähkölaitteiden valinta ja asentaminen. Yleiset säännöt Pienjännitesähköasennukset. Osa 5-52: Sähkölaitteiden valinta ja asentaminen. Johtojärjestelmät Pienjännitesähköasennukset. Osa 5-53: Sähkölaitteiden valinta ja asentaminen. Erottaminen, kytkentä ja ohjaus Pienjännitesähköasennukset. Osa 5-54: Sähkölaitteiden valinta ja asentaminen. Maadoittaminen ja suojajohtimet Pienjännitesähköasennukset. Osa 5-55: Sähkölaitteiden valinta ja asentaminen. Muut sähkölaitteet Pienjännitesähköasennukset. Osa 5-56: Sähkölaitteiden valinta ja asentaminen. Turvajärjestelmät SFS Pienjännitesähköasennukset. Osa 6: Tarkastukset SFS SFS Pienjännitesähköasennukset. Osa 7-701: Erikoistilojen ja -asennusten vaatimukset. Kylpy- ja suihkutilat Pienjännitesähköasennukset. Osa 7-702: Erikoistilojen ja -asennusten vaatimukset. Uima-altaat ja vastaavat 4

5 Suomalaiset SFS-standardit ja suomenkielisinä julkaistut SFS-EN-standardit SFS Pienjännitesähköasennukset. Osa 7-703: Erikoistilojen ja -asennusten vaatimukset. Saunat Vahvistus/julkaisupäivämäärä SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS Pienjännitesähköasennukset. Osa 7-704: Erikoistilojen ja -asennusten vaatimukset. Rakennustyömaat Pienjännitesähköasennukset. Osa 7-705: Erikoistilojen ja -asennusten vaatimukset. Maa- ja puutarhatalouden tilat Pienjännitesähköasennukset. Osa 7-706: Erikoistilojen ja -asennusten vaatimukset. Ahtaat johtavat tilat Pienjännitesähköasennukset. Osa 7-708: Erikoistilojen ja -asennusten vaatimukset. Leirintäalueet Pienjännitesähköasennukset. Osa 7-709: Erikoistilojen ja -asennusten vaatimukset. Venesatamat Pienjännitesähköasennukset. Osa 7-710: Erikoistilojen ja -asennusten vaatimukset. Lääkintätilat Pienjännitesähköasennukset. Osa 7-711: Erikoistilojen ja -asennusten vaatimukset. Näyttelyt, esitykset ja näyttelyosastot Pienjännitesähköasennukset. Osa 7-712: Erikoistilojen ja -asennusten vaatimukset. Aurinkosähköjärjestelmät Pienjännitesähköasennukset. Osa 7-713: Erikoistilojen ja -asennusten vaatimukset. Kalusteet Pienjännitesähköasennukset. Osa 7-714: Erikoistilojen ja -asennusten vaatimukset. Ulkovalaistusasennukset Pienjännitesähköasennukset. Osa 7-715: Erikoistilojen ja -asennusten vaatimukset. Pienoisjännitteiset valaistusjärjestelmät Pienjännitesähköasennukset. Osa 7-717: Erikoistilojen ja -asennusten vaatimukset. Liikkuvat tai siirrettävät laitteistot Pienjännitesähköasennukset. Osa 7-721: Erikoistilojen ja -asennusten vaatimukset. Matkailuajoneuvojen sähköasennukset Pienjännitesähköasennukset. Osa 7-722: Erikoistilojen ja -asennusten vaatimukset. Sähköajoneuvojen syöttö Pienjännitesähköasennukset. Osa 7-729: Erikoistilojen ja -asennusten vaatimukset. Jakokeskusten asentaminen Pienjännitesähköasennukset. Osa 7-740: Erikoistilojen ja -asennusten vaatimukset. Huvipuistojen, tivolien ja sirkusten huvilaitteiden, myyntikojujen ja vastaavien tilapäiset sähköasennukset 5

6 Suomalaiset SFS-standardit ja suomenkielisinä julkaistut SFS-EN-standardit SFS Pienjännitesähköasennukset. Osa 7-753: Erikoistilojen ja -asennusten vaatimukset. Lämmitysjärjestelmät Vahvistus/julkaisupäivämäärä SFS SFS SFS SFS SFS SFS Pienjännitesähköasennukset. Osa 8-801: Täydentävät vaatimukset. Jakeluverkot Pienjännitesähköasennukset. Osa 8-802: Täydentävät vaatimukset. Sähköasennusten korjaus-, muutos- ja laajennustyöt Pienjännitesähköasennukset. Osa 8-804: Täydentävät vaatimukset. Kuivat, kosteat ja märät tilat sekä ulkotilat Pienjännitesähköasennukset. Osa 8-813: Täydentävät vaatimukset. Pistokytkimien valinta ja asentaminen Pienjännitesähköasennukset. Osa 8-814: Täydentävät vaatimukset. Kaapelien asentaminen maahan tai veteen Pienjännitesähköasennukset. Osa 8-803: Täydentävät vaatimukset. Sähkölaitekorjaamot ja laboratoriot SFS-EN /A2 Hälytysjärjestelmät. Murto- ja ryöstöilmaisujärjestelmät. Osa 1: Järjestelmävaatimukset SFS-EN Hälytysjärjestelmät. Turvapuhelinjärjestelmät. Osa 7: Soveltamisohjeet SFS-EN Hälytysjärjestelmät. Yhdistetyt ja integroidut hälytysjärjestelmät. Osa 1: Yleiset vaatimukset SFS-EN SFS-EN Alkolukot. Testausmenetelmät ja suorituskykyvaatimukset. Osa 3: Opas alkolukkojen hankinnoista vastaaville henkilöille ja alkolukkojen käyttäjille Energiakaapelit. Mitoitusjännitteiltään enintään 450/750 V (U0/U) pienjännitekaapelien käyttöohjeet. Osa 2: Erityisohjeet standardisarjan EN mukaisille kaapelityypeille SFS-EN Äänijärjestelmät hätätilannekäyttöön SFS-EN SFS-EN Räjähdysvaaralliset tilat. Osa 10-1: Tilaluokitus. Kaasuräjähdysvaaralliset tilat Räjähdysvaaralliset tilat. Osa 10-2: Tilaluokitus. Pölyräjähdysvaaralliset tilat SFS-EN A1 Räjähdysvaaralliset tilat. Osa 19: Laitteiden korjaus, huolto ja paikkaus SFS-EN Perus- ja turvallisuusperiaatteet ihmisen ja koneen väliselle rajapinnalle, merkinnöille ja tunnistamiselle. Laiteliittimien, johdinpäiden ja johtimien tunnistaminen 6

7 Suomalaiset SFS-standardit ja suomenkielisinä julkaistut SFS-EN-standardit SFS-EN Toiminnallinen turvallisuus. Turva-automaatiojärjestelmät prosessiteollisuussektorille. Osa 1: Rakenne, määritelmät, järjestelmän, laitteiston ja sovellusohjelmoinnin vaatimukset SFS-EN SFS-EN SFS-EN Toiminnallinen turvallisuus. Turva-automaatiojärjestelmät prosessiteollisuussektorille. Osa 2: Ohjeita standardin IEC :2016 soveltamiseen Toiminnallinen turvallisuus. Turva-automaatiojärjestelmät prosessiteollisuussektorille. Osa 3: Ohjeita vaadittavien turvallisuuden eheyden tasojen määrittämiseen Kotien ja rakennusten elektroniikkajärjestelmät (HBES) ja rakennusautomaatio- ja ohjausjärjestelmät (BACS). Osa 1: Yleiset vaatimukset CLC/TS Hälytysjärjestelmät. Ilmoituksensiirtojärjestelmät ja laitteet - Osa 7: Soveltamisohjeet CLC/TS Sähkö- ja elektroniikkalaiteromun keräys-, logistiikka- ja prosessointivaatimukset. Osa 4: Sähkö- ja elektroniikkalaiteromun keräyksen ja siihen liittyvän logistiikan spesifikaatio Vahvistus/julkaisupäivämäärä Ruotsinkielisenä julkaistu SFS-standardi SFS-EN ISO 11554:en Optics and photonics. Lasers and laser-related equipment. Test methods for laser beam power, energy and temporal characteristics (ISO 11554:2017) SFS-EN :en SFS-EN :en SFS-EN :en Light and lighting. Measurement and presentation of photometric data of lamps and luminaires. Part 2: Presentation of data for indoor and outdoor work places Energy performance of buildings. Energy requirements for lighting. Part 1: Specifications, Module M9 Home and Building Electronic Systems (HBES) - Part 3-4: Secure Application Layer, Secure Service, Secure configuration and security Resources SFS-EN :en Home and Building Electronic Systems (HBES) - Part 6-1: Interfaces - Webservice interface

8 SFS-EN :en Railway applications - Electromagnetic compatibility - Part 1: General SFS-EN :en Railway applications - Electromagnetic compatibility - Part 2: Emission of the whole railway system to the outside world SFS-EN :en Railway applications - Electromagnetic compatibility - Part 3-1: Rolling stock - Train and complete vehicle SFS-EN :en Railway applications - Electromagnetic compatibility - Part 3-2: Rolling stock - Apparatus SFS-EN :en Railway applications - Electromagnetic compatibility - Part 4: Emission and immunity of the signaling and telecommunications apparatus SFS-EN :en Railway applications - Electromagnetic compatibility - Part 5: Emission and immunity of fixed power supply installations and apparatus SFS-EN :2011/A4:en SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :2007/A2:en SFS-EN :en SFS-EN :en SFS-EN :en Railway applications - Fixed installations - Electrical safety, earthing and the return circuit - Part 1: Protective provisions against electric shock Railway applications - Insulation coordination - Part 1: Basic requirements - Clearances and creepage distances for all electrical and electronic equipment Railway applications - Insulation coordination - Part 2: Overvoltages and related protection Railway Applications - The Specification and Demonstration of Reliability, Availability, Maintainability and Safety (RAMS) - Part 1: Generic RAMS Process Railway Applications - The Specification and Demonstration of Reliability, Availability, Maintainability and Safety (RAMS) - Part 2: Systems Approach to Safety Alarm systems - Intrusion and hold-up systems - Part 1: System requirements Alarm systems - Intrusion and hold-up systems - Part 2-2: Intrusion detectors - Passive infrared detectors Alarm systems - Intrusion systems - Part 5-3: Requirements for interconnections equipment using radio frequency techniques Alarm systems - Intrusion and hold-up systems - Part 6: Power supplies

9 SFS-EN :en Alarm systems - Social alarm systems - Part 2: Trigger devices SFS-EN :en SFS-EN :en SFS-EN 50153:2014/A1:en Alarm systems - Social alarm systems - Part 7: Application guidelines Railway applications - Fixed installations - Particular requirements for a.c. switchgear - Part 3-1: Measurement, control and protection devices for specific use in a.c. traction systems - Devices Railway applications - Rolling stock - Protective provisions relating to electrical hazards SFS-EN 50155:en Railway applications - Rolling stock - Electronic equipment SFS-EN :2014/A1:en SFS-EN :2015/A1:en SFS-EN :en SFS-EN :en Information technology - Cabling installation - Part 3: Installation planning and practices outside buildings Bushings above 1 kv up to 52 kv and from 250 A to 3,15 ka for liquid filled transformers - Part 3: Requirements for bushing fixations Electric instantaneous water heaters - Part 2-2: Performance requirements - Single point of use electric instantaneous showers - Efficiency Multi-element metallic cables used in analogue and digital communications and control - Part 12-1: Sectional specification for screened cables characterized from 1 MHz up to MHz - Horizontal and building backbone cables SFS-EN :en Communication cables - Specifications for test methods - Part 1-1: Electrical test methods - General requirements SFS-EN :en Communication cables - Specifications for test methods - Part 1-8: Electrical test methods - Attenuation SFS-EN :en Communication cables - Specifications for test methods - Part 1-9: Electrical test methods - Unbalance attenuation (transverse conversion loss TCL transverse conversion transfer loss TCTL) SFS-EN :en SFS-EN :en SFS-EN /A1:en Sound system equipment: headphones and earphones associated with personal music players - Maximum sound pressure level measurement methodology - Part 3: Measurement method for sound dose management Overhead electrical lines exceeding AC 1 kv - Part 2-13: National Normative Aspects (NNA) for ITALY (based on EN :2012) Overhead electrical lines exceeding AC 1 kv - Part 2-13: National Normative Aspects (NNA) for ITALY (based on EN :2012)

10 SFS-EN :en Overhead electrical lines exceeding AC 1 kv Part 2-5: National Normative Aspects (NNA) for DENMARK (based on EN :2012) SFS-EN :en SFS-EN :en SFS-EN :en Overhead electrical lines exceeding AC 1 kv - Part 2-6: National Normative Aspects (NNA) for SPAIN (based on EN :2012) Overhead electrical lines exceeding AC 1 kv - Part 2-8: National Normative Aspects (NNA) for France (based on EN :2012) Overhead electrical lines exceeding AC 1 kv - Part 2-9: National Normative Aspects (NNA) for Great Britain and Northern Ireland (based on EN :2012) SFS-EN 50343:2014/A1:en Railway applications - Rolling stock - Rules for installation of cabling SFS-EN 50360:en SFS-EN 50380:en SFS-EN 50385:en Product standard to demonstrate the compliance of wireless communication devices, with the basic restrictions and exposure limit values related to human exposure to electromagnetic fields in the frequency range from 300 MHz to 6 GHz: devices used next to the ear Marking and documentation requirements for Photovoltaic Modules Product standard to demonstrate the compliance of base station equipment with radiofrequency electromagnetic field exposure limits (110 MHz GHz), when placed on the market SFS-EN :en Alarm systems - Combined and integrated alarm systems - Part 1: General requirements SFS-EN 50401:en SFS-EN 50402:en Product standard to demonstrate the compliance of base station equipment with radiofrequency electromagnetic field exposure limits (110 MHz GHz), when put into service Electrical apparatus for the detection and measurement of combustible or toxic gases or vapours or of oxygen - Requirements on the functional safety of gas detection systems SFS-EN :en Alcohol interlocks - Test methods and performance requirements - Part 3: Guidance for authorities, decision makers, purchasers and users SFS-EN :en Alcohol interlocks - Test methods and performance requirements - Part 7: Installation document SFS-EN :en Railway applications - Energy measurement on board trains - Part 1: General

11 SFS-EN :en Railway applications - Energy measurement on board trains - Part 2: Energy measuring SFS-EN :en Railway applications - Energy measurement on board trains - Part 3: Data handling SFS-EN :en Railway applications - Energy measurement on board trains - Part 4: Communication SFS-EN :en Railway applications - Energy measurement on board trains - Part 5: Conformity assessment SFS-EN 50566:en SFS-EN :en SFS-EN 50593:en Product standard to demonstrate the compliance of wireless communication devices with the basic restrictions and exposure limit values related to human exposure to electromagnetic fields in the frequency range from 30 MHz to 6 GHz: hand-held and body mounted devices in close proximity to the human body Medium power transformers 50 Hz, with highest voltage for equipment not exceeding 36 kv - Part 1: General requirements Electric dishwashers for commercial use - Test methods for measuring the performance SFS-EN :en Information technology - Data centre facilities and infrastructures - Part 4-1: Overview of and general requirements for key performance indicators SFS-EN :en Information technology - Data centre facilities and infrastructures - Part 4-2: Power Usage Effectiveness SFS-EN :en Information technology - Data centre facilities and infrastructures - Part 4-3: Renewable Energy Factor SFS-EN 50620:en Electric cables - Charging cables for electric vehicles SFS-EN :en Collection, logistics & treatment requirements for WEEE - Part 2-3: Treatment requirements for temperature exchange equipment and other WEEE containing VFC and/or VHC SFS-EN :en Collection, logistics & treatment requirements for WEEE - Part 2-4: Treatment requirements for photovoltaic panels SFS-EN :en Household appliances network and grid connectivity - Part 1: General Requirements, Generic Data Modelling and Neutral Messages SFS-EN :en Electric motor-operated tools - Dust measurement procedure - Part 3-3: Particular requirements for transportable planers and thicknessers

12 SFS-EN 50637:en Medical electrical equipment - Particular requirements for the basic safety and essential performance of medical beds for children SFS-EN 50645:en Ecodesign requirements for small power transformers SFS-EN 50647:en Basic standard for the evaluation of workers' exposure to electric and magnetic fields from equipment and installations for the production, transmission and distribution of electricity SFS-EN :en Electric cables - Accessories - Material characterization - Part 1: Fingerprinting for resinous compounds SFS-EN :en Electric cables - Accessories - Material characterization - Part 2: Fingerprinting for heat shrinkable components for low and medium voltage applications up to 20,8/36 (42) kv SFS-EN :en Electric cables - Accessories - Material characterization - Part 3: Fingerprinting for cold shrinkable components for low and medium voltage applications up to 20,8/36 (42) kv SFS-EN 50657:en SFS-EN 50663:en SFS-EN 50664:en SFS-EN 50665:en SFS-EN 50667:en Railways Applications - Rolling stock applications - Software on Board Rolling Stock Generic standard for assessment of low power electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (10 MHz GHz) Generic standard to demonstrate the compliance of equipment used by workers with limits on exposure to electromagnetic fields (0 Hz GHz), when put into service or in situ Generic standard for assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz GHz) Information technology - Automated infrastructure management (AIM) systems - Requirements, data exchange and applications SFS-EN 50672:en Ecodesign requirements for computers and computer servers SFS-EN 50849:en Sound systems for emergency purposes SFS-EN 55011:2016/A1:en SFS-EN :en SFS-EN :2011/A2:en Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity

13 measuring apparatus - Antennas and test sites for radiated disturbance measurements SFS-EN :2015/A1:en SFS-EN :2015/A1:en SFS-EN :2014/A1:en SFS-EN :en SFS-EN 55025:en SFS-EN 55035:en SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :1994/A55:en SFS-EN :1994/A56:en SFS-EN :1994/A52:en SFS-EN :1994/A53:en Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-5: Radio disturbance and immunity measuring apparatus - Antenna calibration sites and reference test sites for 5 MHz to 18 GHz Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-6: Radio disturbance and immunity measuring apparatus - EMC antenna calibration Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-1: Methods of measurement of disturbances and immunity - Conducted disturbance measurements Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers Electromagnetic compatibility of multimedia equipment - Immunity requirements Rotating electrical machines - Part 12: Starting performance of single-speed three-phase cage induction motors Rotating electrical machines - Part 18-42: Partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters - Qualification tests Direct acting indicating analogue electrical measuring instruments and their accessories - Part 1: Definitions and general requirements common to all parts Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 1: Lamp caps Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 1: Lamp caps Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 3: Gauges

14 SFS-EN :1994/A15:en Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 4: Guidelines and general information SFS-EN 60065:2015/A11:en Audio, video and similar electronic apparatus - Safety requirements SFS-EN :en SFS-EN :en Environmental testing - Part 2-18: Tests Test R and guidance: Water Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method SFS-EN :en Railway applications - Electric equipment for rolling stock - Part 1: General service conditions and general rules SFS-EN :en Railway applications - Electric equipment for rolling stock - Part 2: Electrotechnical components - General rules SFS-EN :en SFS-EN :2015/A1:en SFS-EN :en SFS-EN :en SFS-EN :en Explosive atmospheres - Part 13: Equipment protection by pressurized room "p" and artificially ventilated room "v" Explosive atmospheres - Part 18: Equipment protection by encapsulation "m" Explosive atmospheres - Part 29-1: Gas detectors - Performance requirements of detectors for flammable gases Explosive atmospheres - Part 30-1: Electrical resistance trace heating - General and testing requirements Explosive atmospheres - Part 30-2: Electrical resistance trace heating - Application guide for design, installation and maintenance SFS-EN 60081:1998/A6:en Double-capped fluorescent lamps - Performance specifications SFS-EN :en Miniature fuses - Part 5: Guidelines for quality assessment of miniature fuse-links SFS-EN 60137:en Insulated bushings for alternating voltages above V SFS-EN :en SFS-EN :en Hollow metallic waveguides - Part 4: Relevant specifications for circular waveguides Flanges for waveguides - Part 4: Relevant specifications for flanges for circular waveguides SFS-EN 60205:en Calculation of the effective parameters of magnetic piece parts

15 SFS-EN :en Packaging of components for automatic handling - Part 1: Tape packaging of components with axial leads on continuous tapes SFS-EN :en Dependability management - Part 3-3: Application guide - Life cycle costing SFS-EN :en Vacuum cleaners for household use - Part 1: Dry vacuum cleaners - Methods for measuring the performance SFS-EN :en Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire SFS-EN :en Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated, bare or enamelled round copper wire SFS-EN :en Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180 SFS-EN :en Specifications for particular types of winding wires - Part 67: Polyvinyl acetal enamelled rectangular aluminium wire, class 105 SFS-EN :en Specifications for particular types of winding wires - Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120 SFS-EN :en Specifications for particular types of winding wires - Part 69: Polyester or polyesterimide overcoated with polyamide-imide enamelled rectangular aluminium wire, class 220 SFS-EN :en Specifications for particular types of winding wires - Part 70: Polyester glass-fibre wound fused, unvarnished or resin or varnish impregnated, bare or enamelled round copper wire, temperature index 155 SFS-EN :en Specifications for particular types of winding wires - Part 71: Polyester glass-fibre wound fused and resin or varnish impregnated, bare or enamelled round copper wire, temperature index 180 SFS-EN :en Specifications for particular types of winding wires - Part 72: Polyester glass-fibre wound fused, silicone resin or varnish impregnated, bare or enamelled round copper wire, temperature index SFS-EN :2013/A13:en Household and similar electrical appliances - Safety - Part 1: General requirements

16 SFS-EN :2003/A12:en Household and similar electrical appliances - Safety - Part 2-86: Particular requirements for electric fishing machines SFS-EN :2010/A2:en SFS-EN :en Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor Fixed capacitors for use in electronic equipment - Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte SFS-EN 60400:en Lampholders for tubular fluorescent lamps and starterholders SFS-EN :en Magnetic materials - Part 1: Classification SFS-EN :en SFS-EN :2013/A1:en SFS-EN :en SFS-EN 60445:en SFS-EN 60500:en SFS-EN :2007/A11:en SFS-EN :en SFS-EN 60623:en SFS-EN :en Magnetic materials - Part 8-6: Specifications for individual materials - Soft magnetic metallic materials Magnetic materials - Part 15: Methods for the determination of the relative magnetic permeability of feebly magnetic materials Measurement of quartz crystal unit parameters - Part 8 : Test fixture for surface mounted quartz crystal units Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors Underwater acoustics - Hydrophones - Properties of hydrophones in the frequency range 1 Hz to 500 khz Medical electrical equipment - Part 1-8: General requirements for basic safety and essential performance - Collateral Standard: General requirements, tests and guidance for alarm systems in medical electrical equipment and medical electrical systems Connectors for electronic equipment - Part 7-82: Detail specification for 8-way, 12 contacts, shielded, free and fixed connectors, for data transmission with frequencies up to MHz Secondary cells and batteries containing alkaline or other non-acid electrolytes - Vented nickel-cadmium prismatic rechargeable single cells Electroacoustics - Audiometric equipment - Part 1: Equipment for pure-tone and speech audiometry SFS-EN :en Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution

17 SFS-EN :en Specification for plastic films for electrical purposes - Part 2: Methods of test SFS-EN :2011/A1:en SFS-EN :en SFS-EN :2011/A1:en SFS-EN :en SFS-EN :en Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 8: Balanced biaxially oriented polyethylene naphthalate (PEN) films used for electrical insulation Piezoelectric, dielectric and electrostatic oscillators of assessed quality - Part 1: Generic specification Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 247: Heat-shrinkable polyolefin sleeving, dual wall, not flame retarded, thick and medium wall Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines SFS-EN :en Fire hazard testing - Part 8-1: Heat release - General guidance SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :en Fire hazard testing - Part 8-2: Heat release - Summary and relevance of test methods Fire hazard testing - Part 11-2: Test flames - 1 kw nominal premixed flame - Apparatus, confirmatory test arrangement and guidance Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-13: Particular requirements for range hoods and other cooking fume extractors SFS-EN 60715:en Dimensions of low-voltage switchgear and controlgear - Standardized mounting on rails for mechanical support of switchgear, controlgear and accessories SFS-EN :en SFS-EN :en SFS-EN :en Cable networks for television signals, sound signals and interactive services - Part 11: Safety Cable networks for television signals, sound signals and interactive services - Part 13-1: Bandwidth expansion for broadcast signal over FTTH system Cable networks for television signals, sound signals and interactive services - Part 101: System performance of forward paths loaded with digital channels only

18 SFS-EN :2002/A2:en Semiconductor devices - Part 16-1: Microwave integrated circuits - Amplifiers SFS-EN :2002/A2:en SFS-EN :2005/A2:en Semiconductor devices - Part 16-3: Microwave integrated circuits - Frequency converters Semiconductor devices - Part 16-4: Microwave integrated circuits - Switches SFS-EN :en Semiconductor devices - Mechanical and climatic test methods - Part 3: External visual examination SFS-EN :en Semiconductor devices - Mechanical and climatic test methods - Part 4: Damp heat, steady state, highly accelerated stress test (HAST) SFS-EN :en Semiconductor devices - Mechanical and climatic test methods - Part 5: Steady-state temperature humidity bias life test SFS-EN :en Semiconductor devices - Mechanical and climatic test methods - Part 6: Storage at high temperature SFS-EN :en Semiconductor devices - Mechanical and climatic test methods - Part 9: Permanence of marking SFS-EN :en Semiconductor devices - Mechanical and climatic test methods - Part 28: Electrostatic discharge (ESD) sensitivity testing - Charged device model (CDM) - device level SFS-EN :en Semiconductor devices - Mechanical and climatic test methods - Part 43: Guidelines for IC reliability qualification plans SFS-EN :en Nuclear facilities - Electrical equipment important to safety - Qualification SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :en Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance Optical fibres - Part 1-33: Measurement methods and test procedures - Stress corrosion susceptibility Optical fibres - Part 1-48: Measurement methods and test procedures - Polarization mode Dispersion Optical fibres - Part 1-60: Measurement methods and test procedures - Beat length Optical fibres - Part 1-61: Measurement methods and test procedures - Polarization crosstalk Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres

19 SFS-EN :en Optical fibres - Part 2-70: Product specifications - Sectional specification for polarization-maintaining fibres SFS-EN :en SFS-EN :en Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance Optical fibre cables - Part 1-3: Generic specification - Optical cable elements SFS-EN :en Optical fibre cables - Part 2: Indoor cables - Sectional specification SFS-EN :en SFS-EN 60809:2015/A1:en Optical fibre cables - Part 2-22: Indoor cables - Detail specification for multi-simplex breakout optical cables to be terminated with connectors Lamps for road vehicles - Dimensional, electrical and luminous requirements SFS-EN 60810:2015/A1:en Lamps for road vehicles - Performance requirements SFS-EN :2012/A1:en SFS-EN :2012/A1:en SFS-EN :2012/A1:en SFS-EN :2012/A1:en SFS-EN :2012/A1:en SFS-EN :2012/A1:en SFS-EN :2012/A1:en SFS-EN :en Electric and optical fibre cables - Test methods for non-metallic materials - Part 201: General tests - Measurement of insulation thickness Electric and optical fibre cables - Test methods for non-metallic materials - Part 202: General tests - Measurement of thickness of non-metallic sheath Electric and optical fibre cables - Test methods for non-metallic materials - Part 401: Miscellaneous tests - Thermal ageing methods - Ageing in an air oven Electric and optical fibre cables - Test methods for non-metallic materials - Part 410: Miscellaneous tests - Test method for coppercatalyzed oxidative degradation of polyolefin insulated conductors Electric and optical fibre cables - Test methods for non-metallic materials - Part 508: Mechanical tests - Pressure test at high temperature for insulation and sheaths Electric and optical fibre cables - Test methods for non-metallic materials - Part 509: Mechanical tests - Test for resistance of insulations and sheaths to cracking (heat shock test) Electric and optical fibre cables - Test methods for non-metallic materials - Part 511: Mechanical tests - Measurement of the melt flow index of polyethylene compounds Miscellaneous lampholders - Part 1: General requirements and tests

20 SFS-EN /A1:en Miscellaneous lampholders - Part 1: General requirements and tests SFS-EN :en Miscellaneous lampholders - Part 2-3: Particular requirements - Lampholders for double-capped linear LED lamps SFS-EN :en SFS-EN :en Alarm and electronic security systems - Part 11-31: Electronic access control systems - Core interoperability protocol based on Web services Alarm and electronic security systems - Part 11-32: Electronic access control systems - Access control monitoring based on Web services SFS-EN :en Live working - Insulating foam-filled tubes and solid rods - Part 1: Tubes and rods of a circular cross-section SFS-EN 60901:1996/A6:en Single-capped fluorescent lamps - Performance specifications SFS-EN :en SFS-EN :en Photovoltaic devices - Part 1-1: Measurement of current-voltage characteristics of multi-junction photovoltaic (PV) devices Photovoltaic devices - Part 8-1: Measurement of spectral responsivity of multi-junction photovoltaic (PV) devices SFS-EN :en Low-voltage switchgear and controlgear - Part 2: Circuit-breakers SFS-EN :en SFS-EN :1998/A2:en SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :2002/A1:en Low-voltage switchgear and controlgear - Part 5-1: Control circuit devices and switching elements - Electromechanical control circuit devices Low-voltage switchgear and controlgear - Part 5-5: Control circuit devices and switching elements - Electrical emergency stop device with mechanical latching function Information technology equipment - Safety - Part 22: Equipment to be installed outdoors Radio frequency and coaxial cable assemblies - Part 2-5: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 MHz to MHz, IEC connectors Radio frequency and coaxial cable assemblies - Part 2-6: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 MHz to MHz, IEC connectors Electromagnetic compatibility (EMC) - Part 2-2: Environment - Compatibility levels for low-frequency conducted disturbances and signalling in public low-voltage power supply systems

21 SFS-EN :2014/A1:en Electromagnetic compatibility (EMC) - Part 4-5: Testing and measurement techniques - Surge immunity test SFS-EN :en SFS-EN :2005/A1:en SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN 61005:en SFS-EN :2013/A12:en SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :en Electromagnetic compatibility (EMC) - Part 4-10: Testing and measurement techniques - Damped oscillatory magnetic field immunity test Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests Electromagnetic compatibility (EMC) - Part 4-12: Testing and measurement techniques - Ring wave immunity test Electromagnetic compatibility (EMC) - Part 4-31: Testing and measurement techniques - AC mains ports broadband conducted disturbance immunity test Electromagnetic Compatibility (EMC) - Part 4-39: Testing and measurement techniques - Radiated fields in close proximity - Immunity test Radiation protection instrumentation - Neutron ambient dose equivalent (rate) meters Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part 1: General rules Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-011: Particular requirements for refrigerating equipment Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-020: Particular requirements for laboratory centrifuges Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-101: Particular requirements for in vitro diagnostic (IVD) medical equipment Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-202: Particular requirements for electrically operated valve actuators SFS-EN 61057:en Live working - Insulating aerial devices for mounting on a chassis SFS-EN :en Connectors for electronic equipment - Product requirements - Part 2-113: Circular connectors - Detail specification for connectors with

22 M12 screw locking with power and signal contacts for data transmission with frequency up to 100 MHz SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :en Connectors for electrical and electronic equipment - Product requirements - Part 3-104: Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to MHz Connectors for electronic equipment - Product requirements - Part 3-120: Rectangular connectors - Detail specification for rewirable power connectors with snap locking for rated voltage of 250 V d.c. and rated current of 30 A Connectors for electrical and electronic equipment - Product requirements - Part 3-122: Detail specification for 8-way, shielded, free and fixed connectors for I/O and Gigabit Ethernet applications in harsh environments Radio-frequency connectors - Part 11: Sectional specification for RF coaxial connectors with inner diameter of outer conductor 9,5 mm with threaded coupling - Characteristic impedance 50 Ω (type 4,1-9,5) Radio-frequency connectors -Part 59: Sectional specification for type L32-4 and L32-5 threaded multi-pin radio-frequency connectors SFS-EN 61184:en Bayonet lampholders SFS-EN :en SFS-EN :en Printed boards and printed board assemblies - Design and use - Part 7: Electronic component zero orientation for CAD library construction Test methods for electrical materials, printed board and other interconnection structures and assemblies - Part 5-503: General test method for materials and assemblies - Conductive anodic filaments (CAF) testing of circuit boards SFS-EN :en Printed board assemblies - Part 2: Sectional specification - Requirements for surface mount soldered assemblies SFS-EN :en Printed board assemblies - Part 3: Sectional specification - Requirements for through-hole mount soldered assemblies SFS-EN :en Printed board assemblies - Part 4: Sectional specification - Requirements for terminal soldered assemblies SFS-EN :en Fibre optic interconnecting devices and passive components - Fibre optic isolators - Part 1: Generic specification

23 SFS-EN :en Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-2: Special requirements for testing of thinfilm Cadmium Telluride (CdTe) based photovoltaic (PV) modules SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN 61240:en SFS-EN 61242:1998/A13:en SFS-EN 61252:1996/A2:en SFS-EN :2016/A1:en Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-3: Special requirements for testing of thinfilm amorphous silicon based photovoltaic (PV) modules Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-4: Special requirements for testing of thinfilm Cu(In, Ga)(S, Se)2 based photovoltaic (PV) modules Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures Piezoelectric devices - Preparation of outline drawings of surfacemounted devices (SMD) for frequency control and selection - General rules Electrical accessories - Cable reels for household and similar purposes Electroacoustics - Specifications for personal sound exposure meters Electroacoustics - Octave-band and fractional-octave-band filters - Part 2: Pattern-evaluation tests SFS-EN :en Fibre optic communication subsystem test procedures - Part 4-4: Cable plants and links - Polarization mode dispersion measurement for installed links SFS-EN :en SFS-EN :en SFS-EN :en SFS-EN :en Optical amplifiers - Test methods - Part 4-1: Gain transient parameters - Two-wavelength method Optical amplifiers - Part 5-2: Qualification specifications - Reliability qualification for optical fibre amplifiers Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-9: Tests - Shock Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-55: Tests - Strength of mounted adaptor SFS-EN :en Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 3-1: Immunity requirements for safetyrelated systems and for equipment intended to perform safetyrelated functions (functional safety) - General industrial applications

24 SFS-EN 61332:en Soft ferrite material classification SFS-EN :en SFS-EN :2011/A1:en SFS-EN :2014/A1:en Electrostatics - Part 4-7: Standard test methods for specific applications - Ionization Lamp control gear - Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps Lamp controlgear - Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules SFS-EN :en Standard data element types with associated classification scheme - Part 1: Definitions - Principles and methods SFS-EN :en SFS-EN :2015/A11:en SFS-EN :2015/A11:en SFS-EN :2007/A1:en SFS-EN :en SFS-EN :en SFS-EN :2017:en SFS-EN :2017:en SFS-EN :2017:en SFS-EN :2017:en Standard data element types with associated classification scheme for electric components - Part 6: IEC Common Data Dictionary (IEC CDD) quality guidelines Electronic railway equipment - Train communication network (TCN) - Part 2-3: TCN communication profile Electronic railway equipment - Train communication network (TCN) - Part 3-4: Ethernet Consist Network (ECN) Ultrasonics - Pulse-echo scanners - Part 1: Techniques for calibrating spatial measurement systems and measurement of system point-spread function response Wind energy generation systems - Part 12-1: Power performance measurement of electricity producing wind turbines Wind energy generation systems - Part 25-1: Communications for monitoring and control of wind power plants - Overall description of principles and models Wind energy generation systems - Part 25-4: Communications for monitoring and control of wind power plants - Mapping to communication profile Wind energy generation systems - Part 25-5: Communications for monitoring and control of wind power plants - Compliance testing Wind energy generation systems - Part 25-6: Communications for monitoring and control of wind power plants - Logical node classes and data classes for condition monitoring Functional safety - Safety instrumented systems for the process industry sector - Part 1: Framework, definitions, system, hardware and application programming Requirements