Erikoisnumero tammikuu 2013 SESKOn alueelta julkaistut ja vahvistetut SFS-STANDARDIT 2012

Transkriptio

1 Erikoisnumero tammikuu 2013 Ajankohtaista sähkö- ja elektroniikka-alan standardoinnista SESKOn alueelta julkaistut ja vahvistetut SFS-STANDARDIT 2012 SISÄLTÖ IEC-, EN- ja SFS-EN-standardien valmistelu... 2 SFS-standardien valmistelu... 3 Johdanto... 3 SESKOn alueelta julkaistut ja vahvistetut standardit vuonna 2012 Suomenkielisinä julkaistut SFS-standardit, teknilliset raportit ja teknilliset spesifikaatiot... 4 Ruotsinkielisinä julkaistut SFS-standardit... 6 Luetteloimismenettelyllä vahvistetut SFS-standardit ja e-standardit... 8 SESKOn valmistelemat, vuonna 2012 julkaistut SFS-käsikirjat Lisätietoa standardeista ja ja direktiiveistä

2 IEC-, EN- ja SFS-EN-standardien valmistelu. Rinnakkaismenettely. SFS-standardien valmistelu Johdanto Ehdotus uudeksi työkohteeksi (NP) Ylläpitomenettely Valmisteluvaihe Lausuntokierros (CD) Äänestyskierros (CDV) Muodollinen loppuäänestys (FDIS) Parallel UAP Parallel FDIS Äänestys WG/PT/MT -ryhmien kansalliset jäsenet Lausunto tarvittaessa Kansallinen lausuntokierros Äänestys (IEC & CENELEC) Lausunto tarvittaessa (CENELEC) Äänestykset ehdotuksiin (IEC & CENELEC) IEC-standardi EN-standardi SFS-EN-standardi (Kansalliset toimenpiteet) IECstandardi tai HDasiakirja SFSstandardin uusiminen Kansallinen aloite Standardin valmistelu SK-komiteassa Kansallinen lausuntokierros Standardin täsmentäminen SESKOn hyväksyntä SFS:n vahvistus Sähkö- ja elektroniikka-alalla standardit valmistellaan neljän pääperiaatteen mukaisesti: 1. Laaditaan maailmanlaajuinen IEC-standardi. 2. Laaditaan maailmanlaajuinen IEC-standardi, joka IEC/CENELEC-rinnakkaismenettelyllä vahvistetaan eurooppalaiseksi ENstandardiksi. Tämä on otettava kansallisesti käyttöön identtisenä SFS-EN-standardina. 3. Laaditaan eurooppalainen EN-standardi, joka on otettava kansallisesti käyttöön identtisenä SFS-EN-standardina. 4. Laaditaan kansallinen SFS-standardi joko IEC-standardin pohjalta tai puhtaasti kansallisista lähtökohdista silloin, kun vastaavaa EN-standardia ei ole. EN-standardi on saatettava identtiseksi SFS-EN-standardiksi. Tämä tehdään yksinkertaisimmillaan luettelointimenettelyllä. Tässä menettelyssä ei julkaista kansallisesti erillistä asiakirjaa, vaan asiasta ainoastaan ilmoitetaan SFS-tiedotuksessa. Lisäksi SFS-EN-standardin tunnus ja nimi ilmoitetaan Suomen Standardisoimisliitto SFS ry:n verkkosivulla SFS-standardiluettelossa. Eräät SFS-EN-standardit on julkaistu suomeksi. Standardin julkaiseminen (SFS) SFS-standardi Tässä luettelossa esitetään SESKOn toimialueelta vuonna 2012 julkaistut suomen- tai ruotsinkieliset SFS-standardit sekä luetteloimalla vahvistetut englanninkieliset SFS-standardit. SESKO-lehti. Ajankohtaista sähköalan standardoinnista. ISSN Sisältöä saa lainata lähteen mainiten. JULKAISIJA: SESKO ry, Särkiniementie 3, 00210, HELSINKI, p , faksi , TOIMITUS: Päätoimittaja Sinikka Hieta-Wilkman. Standardiluettelon toimittaja: Juha Vesa. Taitto: Tinni Karakorpi. Paino: Valopaino Oy. Vuosikerta nroa/2013. SESKOn alueelta julkaistut ja vahvistetut SFS-standardit

3 Suomenkielisinä julkaistut SFS-standardit, teknilliset raportit ja spesifikaatiot SFS 2529 Vaihtosähköenergian mittaus. Energiamittarin alusta SFS 2532 Monimittarikeskukset SFS 5601 Sähköenergiamittareiden tilat SFS 5993 Kotitalouksiin ja vastaaviin käyttöihin tarkoitetut jatkojohdot SFS SFS SFS Pienjännitesähköasennukset. Osa 1: Perusperiaatteet, yleisten ominaisuuksien määrittely ja määritelmät Pienjännitesähköasennukset. Osa 4-41: Suojausmenetelmät. Suojaus sähköiskulta Pienjännitesähköasennukset. Osa 4-42: Suojausmenetelmät. Suojaus lämmön vaikutuksilta SFS Pienjännitesähköasennukset. Osa 4-43: Suojausmenetelmät. Ylivirtasuojaus SFS SFS SFS SFS SFS SFS SFS Pienjännitesähköasennukset. Osa 4-44: Suojausmenetelmät. Suojaus jännitehäiriöiltä ja sähkömagneettisilta häiriöiltä Pienjännitesähköasennukset. Osa 5-51: Sähkölaitteiden valinta ja asentaminen. Yleiset säännöt Pienjännitesähköasennukset. Osa 5-52: Sähkölaitteiden valinta ja asentaminen. Johtojärjestelmät Pienjännitesähköasennukset. Osa 5-53: Sähkölaitteiden valinta ja asentaminen. Erottaminen, kytkentä ja ohjaus Pienjännitesähköasennukset. Osa 5-54: Sähkölaitteiden valinta ja asentaminen. Maadoittaminen ja suojajohtimet Pienjännitesähköasennukset. Osa 5-55: Sähkölaitteiden valinta ja asentaminen. Muut sähkölaitteet Pienjännitesähköasennukset. Osa 5-56: Sähkölaitteiden valinta ja asentaminen. Turvajärjestelmät SFS Pienjännitesähköasennukset. Osa 6: Tarkastukset SFS SFS SFS SFS SFS SFS SFS SFS SFS Pienjännitesähköasennukset. Osa 7-701: Erikoistilojen ja -asennusten vaatimukset. Kylpy- ja suihkutilat Pienjännitesähköasennukset. Osa 7-702: Erikoistilojen ja -asennusten vaatimukset. Uima-altaat ja vastaavat Pienjännitesähköasennukset. Osa 7-703: Erikoistilojen ja -asennusten vaatimukset. Saunat Pienjännitesähköasennukset. Osa 7-704: Erikoistilojen ja -asennusten vaatimukset. Rakennustyömaat Pienjännitesähköasennukset. Osa 7-705: Erikoistilojen ja -asennusten vaatimukset. Maa- ja puutarhatalouden tilat Pienjännitesähköasennukset. Osa 7-706: Erikoistilojen ja -asennusten vaatimukset. Ahtaat johtavat tilat Pienjännitesähköasennukset. Osa 7-708: Erikoistilojen ja -asennusten vaatimukset. Leirintäalueet Pienjännitesähköasennukset. Osa 7-709: Erikoistilojen ja -asennusten vaatimukset. Venesatamat Pienjännitesähköasennukset. Osa 7-710: Erikoistilojen ja -asennusten vaatimukset. Lääkintätilat SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS SFS Pienjännitesähköasennukset. Osa 7-711: Erikoistilojen ja -asennusten vaatimukset. Näyttelyt, esitykset ja näyttelyosastot Pienjänniteasennukset. Osa 7-712: Erikoistilojen ja -asennusten vaatimukset. Valosähköiset tehonsyöttöjärjestelmät Pienjännitesähköasennukset. Osa 7-713: Erikoistilojen ja -asennusten vaatimukset. Kalusteet Pienjännitesähköasennukset. Osa 7-714: Erikoistilojen ja -asennusten vaatimukset. Ulkovalaistuasennukset Pienjännitesähköasennukset. Osa 7-715: Erikoistilojen ja -asennusten vaatimukset. Pienoisjännitteiset valaistusjärjestelmät Pienjännitesähköasennukset. Osa 7-717: Erikoistilojen ja -asennusten vaatimukset. Liikkuvat tai siirrettävät laitteistot Pienjännitesähköasennukset. Osa 7-721: Erikoistilojen ja -asennusten vaatimukset. Matkailuvaunujen ja -autojen sähköasennukset Pienjännitesähköasennukset. Osa 7-722: Erikoistilojen ja -asennusten vaatimukset. Sähköajoneuvojen syöttö Pienjännitesähköasennukset. Osa 7-729: Erikoistilojen ja -asennusten vaatimukset. Jakokeskusten asentaminen Pienjännitesähköasennukset. Osa 7-740: Erikoistilojen ja -asennusten vaatimukset. Huvipuistojen, tivolien ja sirkusten huvilaitteiden, myyntikojujen ja vastaavien tilapäiset sähköasennukset Pienjännitesähköasennukset. Osa 7-753: Erikoistilojen ja -asennusten vaatimukset. Lämmitysjärjestelmät Pienjännitesähköasennukset. Osa 8-801: Täydentävät vaatimukset. Jakeluverkot Pienjännitesähköasennukset. Osa 8-802: Täydentävät vaatimukset. Sähköasennusten korjaus-, muutos- ja laajennustyöt Pienjännitesähköasennukset. Osa 8-803: Täydentävät vaatimukset. Sähkölaitekorjaamot Pienjännitesähköasennukset. Osa 8-804: Täydentävät vaatimukset. Kuivat, kosteat ja märät tilat sekä ulkotilat Pienjännitesähköasennukset. Osa 8-812: Täydentävät vaatimukset. Asennuspistoliittimien asennus ja käyttö Pienjännitesähköasennukset. Osa 8-813: Täydentävät vaatimukset. Pistokytkimien valinta ja asentaminen Pienjännitesähköasennukset. Osa 8-814: Täydentävät vaatimukset. Kaapelien asentaminen maahan tai veteen SFS-IEC Sähköteknillinen sanasto. Yleisreleet SFS-IEC Sähköteknillinen sanasto. Aikareleet SFS-IEC Sähköteknillinen sanasto. Mittausreleet SFS-IEC /A1 Sähköteknillinen sanasto. Osa 617: Organisaatio/sähkömarkkinat SFS-EN Hälytysjärjestelmät. Ilmoituksensiirtojärjestelmät ja laitteet. Osa 1: Yleiset vaatimukset ilmoituksensiirtojärjestelmille SFS-EN Akkujen ja akkuasennusten turvallisuusvaatimukset. Osa 1: Yleiset vaatimukset SFS-EN Valosähköisten moduulien datalehdet ja nimikilpitiedot SFS-EN 50408/A1 SFS-EN Kotitaloussähkölaitteiden ja vastaavien turvallisuus. Ajoneuvojen sisälämmittimien erityisvaatimukset Tekniset vaatimukset yleisen pienjännitejakeluverkon kanssa rinnan toimiville mikrogeneraattoreille SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2012 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit

4 SFS-EN CLC/TR :fi Yleiset vaatimukset kotien ja rakennusten elektroniikkajärjestelmille (HBES) sekä rakennusautomaatio ja ohjausjärjestelmille (BACS). Osa 4-1: Yleiset toiminnallisen turvallisuuden vaatimukset rakennusten elektronisiin järjestelmiin (HBES) ja rakennusautomaatio- ja ohjausjärjestelmiin (BACS) integroitaville tuotteille Yleiset vaatimukset kotien ja rakennusten elektroniikkajärjestelmille (HBES) sekä rakennusautomaatio- ja ohjausjärjestelmille (BACS). Osa 6-3: HBES-asennukset. Järjestelmän arviointi ja toimintoluokituksen määrittely CLC/TR 50531:fi Hälytysjärjestelmät. Termit ja määritelmät SFS-EN CENELECin standardijännitteet SFS-EN /A15 Kotitaloussähkölaitteiden ja vastaavien turvallisuus. Osa 1: Yleiset vaatimukset IEC/TR :fi SFS-EN /A11 SFS-EN /A11 SFS-EN /A11 Sähkömagneettinen yhteensopivuus (EMC). Osa 5: Ohjeita sähkömagneettisten häiriövaikutusten minimoimiseen asennuksissa. Kappale 1: Yleiset näkökohdat Sähköasennusten asennusputkijärjestelmät. Osa 21: Jäykkien asennusputkijärjestelmien erityisvaatimukset Sähköasennusten asennusputkijärjestelmät. Osa 22: Taipuisien asennusputkijärjestelmien erityisvaatimukset Sähköasennusten asennusputkijärjestelmät. Osa 23: Taivuteltavien asennusputkijärjestelmien erityisvaatimukset SFS-EN Teknisen informaation ja dokumentaation jäsentely SFS-EN Osaluetteloiden ja kohdeluetteloiden laatiminen SFS-EN 62115/A2 Sähkökäyttöisten lelujen turvallisuus IEC/TS :fi SFS-EN Ruotsinkielisinä julkaistut SFS-standardit SFS :sv Teollisuuden tietoliikenneverkot. Verkkojen ja järjestelmien tietoturvallisuus. Osa 1-1: Terminologia, käsitteet ja mallit Käyttöohjeiden laatiminen. Jäsentäminen, sisältö ja esittäminen. Osa 1: Yleiset periaatteet ja yksityiskohtaiset vaatimukset Lågspänningselinstallationer. Del 1: Grundläggande principer, definitioner och bestämning av allmänna egenskaper SFS :sv Lågspänningselinstallationer. Del 4-41: Skyddsmetoder. Skydd mot elchock SFS :sv Lågspänningselinstallationer. Del 4-42: Skyddsmetoder. Skydd mot termiska påverkningar SFS :sv Lågspänningselinstallationer. Del 4-43: Skyddsmetoder. Skydd mot överström SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv Lågspänningselinstallationer. Del 4-44: Skyddsmetoder. Skydd mot spänningsstörningar och elektromagnetiska störningar Lågspänningselinstallationer. Del 5-51: Val och installation av elmateriel. Allmänna regler Lågspänningselinstallationer. Del 5-52: Val och installation av elmateriel. Ledningssystem Lågspänningselinstallationer. Del 5-53: Val och installation av elmateriel. Frånskiljning, koppling och manövrering Lågspänningselinstallationer. Del 5-54: Val och installering av elmateriel. Jordning och skyddsledare Lågspänningselinstallationer. Del 5-55: Val och installation av elmateriel. Annan elmateriel SFS :sv Lågspänningselinstallationer. Del 5-56: Val och installation av elektrisk materiel. Säkerhetsystem SFS :sv Lågspänningselinstallationer. Del 6: Kontroller SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv SFS :sv Lågspänningselinstallationer. Del 7-701: Krav på elinstallationer och utrymmen av särskilt slag. Bad- och duschutrymmen Lågspänninsgelinstallationer. Del 7-702: Krav på elinstallationer och utrymmen av särskilt slag. Simbassänger och motsvarande Lågspänninsgselinstallationer. Del 7-703: Krav på elinstallationer och utrymmen av särskilt slag. Basturum Lågspänningselinstallationer. Del 7-704: Krav på elinstallationer och utrymmen av särskilt slag. Byggplatser Lågspänningselinstallationer. Del 7-705: Krav på elinstallationer och utrymmnen av särskilt slag. Anläggningar inom jord- och trädgårdsbruk Lågspänningselinstallationer. Del 7-706: Krav på elinstallationer och utrymmen av särskilt slag. Trängä ledande utrymmen Lågspänningselinstallationer. Del 7-708: Krav på elinstallationer och utrymmen av särskilt slag. Campingområden Lågspänningselinstallationer. del 7-709: Krav på elinstallationer och utrymmen av särskilt slag. Båthamnar Lågspänningselinstallationer. Del 7-710: Krav på elinstallationer och utrymmen av särskilt slag. Medicinska utrymmen Lågspänningselinstallationer. Del 7-711: Krav på elinstallationer och utrymmen av särskilt slag. Utställningar, förevisningar och utställninsavdelningar Lågspänningselinstallationer. Del 7-712: Krav på elinstallationer och utrymmen av särskilt slag. Solelektriska kraftmatningssystem Lågspänningselinstallationer. Del 7-713: Krav på elinstallationer och utrymmen av särskilt slag. Möbler Lågspänningselinstallationer. Del 7-714: Krav på elinstallationer och utrymmen av särskilt slag. Belysninginstallationer utomhus Lågspänningselinstallationer. Del 7-715: Krav på elinstallationer och utrymmen av särskilt slag. Belysningssystem för klenspänning Lågspänningselinstallationer. Del 7-717: Krav på elinstallationer och utrymmen av särskilt slag. Rörliga eller flyttbara anläggningar Låspänningselinstalaltioner. Del 7-721: Krav på elinstallationer och utrymmen av särskilt slag. Elinstallationer i campingfordon Låspänningselinstalaltioner. Del 7-722: Krav på elinstallationer och utrymmen av särskilt slag. Matning av elektriska fordon Låspänningselinstalaltioner. Del 7-729: Krav på elinstallationer och utrymmen av särskilt slag. Installation av fördelningscentraler Lågspänningselinstallationer. Del 7-740: Krav på elinstallationer och utrymmen av särskilt slag. Tillfälliga elinstallationer för nöjesanläggningar, försäljingsstånd och liknande på nöjesfält, tivolin och cirkusar Lågspänningselinstallationer. Del 7-753: Krav på elinstallationer och utrymmen av särksilt slag. Uppvärmingssystem Lågspänningselinstallationer. Del 8-801: Kompletterande krav. Distributionsnät Lågspänningselinstallationer. Del 8-802: Kompletterande krav. Reparation, ändring och utökning av elinstallationer Lågspänningselinstallationer. Del 8-803: Kompletterande krav. Elreparationsverkstäder och ellaboratorier SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2012 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit

5 SFS :sv SFS :sv SFS :sv SFS :sv Lågspänningselinstallationer. Del 8-804: Kopletterande krav. Torra, fuktiga och våta utrymmen samt utrymmen utomhus Lågspänningselinstallationer. Del 8-812: Kompletterande krav. Installation och användning av snabbkopplingsdon Lågspänningselinstallationer. Del 8-813: Kompletterande krav. Val och installation av uttagsdon Lågspänningselinstallationer. Del 8-814: Kompletterande krav. Förläggning av kabel i mark eller vatten Luetteloimismenettelyllä vahvistetut SFS-standardit, e-standardit yms. SFS-EN ISO :en Lasers and laser-related equipment. Determination of laser resistance of tracheal tubes. Part 1: Tracheal tube shaft (ISO :2011) SFS-EN 12665:en Light and lighting. Basic terms and criteria for specifying lighting requirements SFS-EN A1:en SFS-EN ISO :en SFS-EN ISO :en SFS-EN ISO :en SFS-EN SFS-EN Light and lighting. Measurement and presentation of photometric data of lamps and luminaires. Part 1: Measurement and file format Lasers and laser-related equipment. Test methods for laser-induced damage threshold. Part 1: Definitions and general principles (ISO :2011) Lasers and laser-related equipment. Test methods for laser-induced damage threshold. Part 2: Threshold determination (ISO :2011) Lasers and laser-related equipment. Test methods for laser-induced damage threshold. Part 3: Assurance of laser power (energy) handling capabilities (ISO :2011) Alarm systems. CCTV surveillance systems for use in security applications. Part 5-1: Video transmission. General video transmission performance requirements Alarm systems. CCTV surveillance systems for use in security applications. Part 5-2: IP Video transmission protocols SFS-EN Power transformer and reactor fittings. Part 12: Fans SFS-EN Multi-element metallic cables used in analogue and digital communication and control. Part 8: Specification for type 1 cables characterised up SFS-EN Electromagnetic compatibility. Road traffic signal systems. Product standard SFS-EN Railway applications. Current collection systems. Requirements for and validation of measurements of the dynamic interaction between pantograph and overhead contact line SFS-EN /A1 Lead-acid starter batteries. Part 1: General requirements and methods of test SFS-EN SFS-EN SFS-EN SFS-EN Connector sets and interconnect components to be used in optical fibre communication systems. Product specifications. Part 16-1: Type LF3 APC simplex terminated on IEC category B1.1 and B1.3 single mode fibre with titanium composite ferrule for category C Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances. Part 1: General requirements and test methods Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances. Part 2: Performance requirements for apparatus used in statutory inspections and assessment Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances. Part 3: Performance requirements for apparatus used in non-statutory servicing of gas fired heating appliances SFS-EN SFS-EN 50401/A1 SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN /A1 SFS-EN /A1 SFS-EN SFS-EN SFS-EN SFS-EN Railway applications. Power supply and rolling stock. Technical criteria for the coordination between power supply (substation) and rolling stock to achieve interoperability Product standard to demonstrate the compliance of fixed equipment for radio transmission (110 MHz - 40 GHz) intended for use in wireless telecommunication networks with the basic restrictions or the reference levels related to general public human exposure to radio frequency electromagnetic fields, when put into service Fibre organisers and closures to be used in optical fibre communication systems. Product specifications. Part 2-2: Sealed pan fibre splice closures type 1, for category S & A Fibre organisers and closures to be used in optical fibre communication systems. Product specifications. Part 2-3: Sealed inline fibre splice closures Type 1, for category S & A Fibre organisers and closures to be used in optical fibre communication systems. Product specifications. Part 2-4: Sealed dome fibre splice closures Type 1, for category S & A Fibre organisers and closures to be used in optical fibre communication systems. Product specification. Part 3-1: Fibre management system, splice wall box, for category C & G Fibre organisers and closures to be used in optical fibre communication systems. Product specifications. Part 3-3: Singlemode optical fibre fusion splice protectors Cables for indoor residential telecommunication installations. Part 1: Unscreened cables. Grade Cables for indoor residential telecommunication installations. Part 2: Screened cables. Grade Cables for indoor residential telecommunication installations. Part 4: Cables up to 1200 MHz. Grade Three-phase oil-immersed distribution transformers 50 Hz, from 50 kva to 2500 kva with highest voltage for equipment not exceeding 36 kv. Part 1: General requirements Three phase oil-immersed distribution transformers 50 Hz, from 50 kva to 2500 kva with highest voltage for equipment not exceeding 36 kv. Part 4: Requirements and tests concerning pressurised corrugated tanks Railway applications. Rolling stock. Electrical connectors, requirements and test methods Industrial connector sets and interconnect components to be used in optical fibre control and communication systems. Product specifications. Part 1-1: Type SC-RJ PC industrial terminated on EN category A1a and A1b multimode fibre to meet the requirements of category I (industrial environments) as specified in IEC Industrial connector sets and interconnect components to be used in optical fibre control and communication systems. Product specifications. Part 2-1: Type ODVA PC industrial terminated on EN category A1a and A1b multimode fibre to meet the requirements of category I (industrial environments) as specified in EN and IEC Railway applications. Fixed installations. D.C. surge arresters and voltage limiting devices. Part 1: Surge arresters SFS-EN Railway applications. Three-phase train line voltage characteristics SFS-EN Three-phase dry-type distribution transformers 50 Hz, from 100 to 3150 kva, with highest voltage for equipment not exceeding 36 kv. Part 1: General requirements SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2012 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit

6 SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN /A47 SFS-EN /A42 SFS-EN /A43 SFS-EN /A44 SFS-EN /A43 SFS-EN /A44 SFS-EN /A45 SFS-EN /A14 SFS-EN SFS-EN Electrical apparatus for the detection and measurement of combustible gases in car parks and tunnels. Part 1: General performance requirements and test methods for the detection and measurement of carbon monoxide and nitrogen oxides Power frequency overvoltage protective device for household and similar applications (POP) Railway applications. Requirements for running capability in case of fire on board of rolling stock Requirements for automatic reclosing devices for circuit breakers-rcbos-rccbs for household and similar users (ARDs) External a.c. - d.c. and a.c. - a.c. power supplies. Determination of no-load power and average efficiency of active modes Collection, logistics & treatment requirements for end-of-life household appliances containing volatile fluorocarbons or volatile hydrocarbons Safety of hand-held electric motor operated tools. Particular requirements for spray guns Rotating electrical machines. Part 16: Excitation systems for synchronous machines. Chapter 1: Definitions and safety. Part 1: Lamp caps and safety. Part 2: Lampholders and safety. Part 2: Lampholders and safety. Part 2: Lampholders and safety. Part 3: Gauges and safety. Part 3: Gauges and safety. Part 3: Gauges and safety. Part 4: Guidelines and general information Environmental Testing. Part 2-83: Tests. Test Tf: Solderability testing of electronic components for surface mounting devices (SMD) by the wetting balance method using solder paste Environmental testing. Part 3-1: Supporting documentation and guidance. Cold and dry heat tests SFS-EN Power transformers. Part 1: General SFS-EN Power transformers. Part 2: Temperature rise SFS-EN Explosive atmospheres. Part 11: Equipment protection by intrinsic safety i SFS-EN Power transformers. Part 16: Transformers for wind turbine applications SFS-EN Surge arresters. Part 8: Metal-oxide surge arresters with external series gap (EGLA) for overhead transmission and distribution lines of a.c. systems above 1 kv SFS-EN Fixed resistors for use in electronic equipment. Part 1: Generic specification SFS-EN /A1 Miniature fuses. Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links SFS-EN AC motor capacitors. Part 2: Motor start capacitors SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN /A2 SFS-EN /A1 SFS-EN /A11 SFS-EN /A11 SFS-EN /A2 SFS-EN SFS-EN /A11 SFS-EN /A2 SFS-EN /A11 SFS-EN /A11 SFS-EN /A13 SFS-EN /A11 SFS-EN /A2 SFS-EN /A2 SFS-EN /A11 SFS-EN /A11 SFS-EN /A11 SFS-EN /A2 Measuring relays and protection equipment. Part 22-5: Electrical disturbance tests. Surge immunity test Low-voltage fuses. Part 6: Supplementary requirements for fuse-links for the protection of solar photovoltaic energy systems Fluids for electrotechnical applications. Unused mineral insulating oils for transformers and switchgear Dependability management. Part 3-12: Application guide. Integrated logistic support Plugs, socket-outlets and couplers for industrial purposes. Part 2: Dimensional interchangeability requirements for pin and contact -tube accessories Switched socket-outlets and couplers for industrial purposes. Part 4: Switched socket-outlets and connectors with or without interlock Household and similar electrical appliances. Safety. Part 2-14: Particular requirements for kitchen machines Household and similar electrical appliances. Safety. Part 2-15: Particular requirements for appliances for heating liquids Household and similar electrical appliances. Safety. Part 2-16: Particular requirements for food waste disposers Household and similar electrical appliances. Safety. Part 2-25: Particular requirements for microwave ovens, including combination microwave ovens Household and similar electrical appliances. Safety. Part 2-30: Particular requirements for room heaters Household and similar electrical appliances. Safety. Part 2-35: Particular requirements for instantaneous water heaters Household and similar electrical appliances. Safety. Part 2-36: Particular requirements for commercial electric cooking ranges, ovens, hobs and hob elements Household and similar electrical appliances. Safety. Part 2-37: Particular requirements for commercial electric deep fat fryers Household and similar electrical appliances. Safety. Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers Household and similar electrical appliances. Safety. Part 2-42: Particular requirements for commercial electric forced convection ovens, steam cookers and steam-convection ovens Household and similar electrical appliances. Safety. Part 2-44: Particular requirements for ironers Household and similar electrical appliances. Safety. Part 2-45: Particular requirements for portable heating tools and similar appliances Household and similar electrical appliances. Safety. Part 2-47: Particular requirements for commercial electric boiling pans Household and similar electrical appliances. Safety. Part 2-48: Particular requirements for commercial electric grillers and toasters Household and similar electrical appliances. Safety. Part 2-49: Particular requirements for commercial electric appliances for keeping food and crockery warm Household and similar electrical appliances. Safety. Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2012 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit

7 SFS-EN SFS-EN /A2 SFS-EN /A2 SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN /A2 SFS-EN /A2 Household and similar electrical appliances. Safety. Part 2-53: Particular requirements for sauna heating appliances and infrared cabins Household and similar electrical appliances. Safety. Part 2-66: Particular requirements for water-bed heaters Household and similar electrical appliances. Safety. Part 2-81: Particular requirements for foot warmers and heating mats Fixed capacitors for use in electronic equipment. Part 2: Sectional specification. Fixed metallized polyethylene terephthalate film dielectric d.c. capacitors Fixed capacitors for use in electronic equipment. Part 13: Sectional specification. Fixed polypropylene film dielectric metal foil d.c. capacitors Fixed capacitors for use in electronic equipment. Part 21: Sectional specification. Fixed surface mount multilayer capacitors of ceramic dielectric, Class Fixed capacitors for use in electronic equipment. Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class Incandescent lamps. Safety specifications. Part 1: Tungsten filament lamps for domestic and similar general lighting purposes Incandescent lamps. Safety specifications. Part 2: Tungsten halogen lamps for domestic and similar lighting purposes SFS-EN Method of sampling insulating liquids SFS-EN SFS-EN SFS-EN Industrial-process control valves. Part 8-2: Noise considerations. Laboratory measurement of noise generated by hydrodynamic flow through control valves Electrical insulating materials. Determination of the effects of ionizing radiation. Part 5: Procedures for assessment of ageing in service Oil-filled electrical equipment. Sampling of gases and analysis of free and dissolved gases. Guidance SFS-EN Luminaires. Part 2: Particular requirements. Recessed luminaires SFS-EN /A1 Luminaires. Part 2-13: Particular requirements. Ground recessed luminaires SFS-EN /A1 SFS-EN /A11 SFS-EN /A11 SFS-EN /A11 SFS-EN /A11 SFS-EN /A11 SFS-EN /A11 SFS-EN /A11 SFS-EN /A11 SFS-EN /A11 Luminaires. Part 2: Particular requirements. Section 18: Luminaires for swimming pools and similar applications Medical electrical equipment. Part 1: General requirements for basic safety and essential performance Medical electrical equipment. Part 2-2: Particular requirements for the basic safety and essential performance of high frequency surgical equipment and high frequency surgical accessories Medical electrical equipment. Part 2-19: Particular requirements for the basic safety and essential performance of infant incubators Medical electrical equipment. Part 2-20: Particular requirements for basic safety and essential performance of infant transport incubators Medical electrical equipment. Part 2-21: Particular requirements for the basic safety and essential performance of infant radiant warmers Medical electrical equipment. Part 2-29: Particular requirements for the basic safety and essential performance of radiotherapy simulators Medical electrical equipment. Part 2-33: Particular requirements for the basic safety and essential performance of magnetic resonance equipment for medical diagnosis Medical electrical equipment. Part 2-37: Particular requirements for the basic safety and essential performance of ultrasonic medical diagnostic and monitoring equipment Medical electrical equipment. Part 2-39: Particular requirements for basic safety and essential performance of peritoneal dialysis equipment SFS-EN /A11 SFS-EN /A11 SFS-EN /A11 SFS-EN Medical electrical equipment. Part 2-41: Particular requirements for basic safety and essential performance of surgical luminaires and luminaires for diagnosis Medical electrical equipment. Part 2-44: Particular requirements for the safety and essential performance of X-ray equipment for computed tomography Medical electrical equipment. Part 2-50: Particular requirements for the basic safety and essential performance of infant phototherapy equipment Combined flexible materials for electrical insulation. Part 1: Definitions and general requirements SFS-EN High pressure sodium vapour lamps. Performance specifications SFS-EN Switches for household and similar fixed electrical installations. Part 2-6: Fireman s switches for exterior and interior signs and luminaries SFS-EN /A1 Plastic films for electrical purposes. Part 3: Specifications for individual materials. Sheet 1: Biaxially oriented polypropylene (PP) film for capacitors SFS-EN Industrial electroheating equipment. Test methods for direct arc furnaces SFS-EN Quartz crystal controlled oscillators of assessed quality. Part 6: Phase jitter measurement method for quartz crystal oscillators and SAW oscillators. Application guide SFS-EN Industrial electroheating equipment. Test methods for submerged-arc furnaces SFS-EN Flexible insulating sleeving. Part 2: Methods of test SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN Flexible insulating sleeving. Part 3: Specifications for individual types of sleeving. Sheets 116 and 117: Extruded polychloroprene. General purpose Fire hazard testing. Part 6-2: Smoke obscuration. Summary and relevance of test methods Fire hazard testing. Part 7-2: Toxicity of fire effluent. Summary and relevance of test methods Fire hazard testing. Part 7-3: Toxicity of fire effluent. Use and interpretation of test results Fire hazard testing. Part 11-4: Test flames. 50 W flame. Apparatus and conformational test method Household and similar electrical appliances. Test code for the determination of airborne acoustical noise. Part 2-4: Particular requirements for washing machines and spin extractors Household and similar electrical appliances. Test code for the determination of airborne acoustical noise. Part 2-10: Particular requirements for electric cooking ranges, ovens, grills, microwave ovens and any combination of these SFS-EN Household microwave ovens. Methods for measuring performance SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN /A11 SFS-EN Method for the determination of the space required by capacitors and resistors with unidirectional terminations Automatic electrical controls for household and similar use. Part 1: General requirements Medical electrical equipment. Dosimeters with ionization chambers as used in radiotherapy Hand-held motor-operated electric tools. Safety. Part 2-3: Particular requirements for grinders, polishers and disk-type sanders Hand-held motor-operated electric tools. Safety. Part 2-4: Particular requirements for sanders and polishers other than disk type Hand-held motor-operated electric tools. Safety. Part 2-22: Particular requirements for cut-off machines SFS-EN Optical fibres. Part 2: Product specifications. General SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2012 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit

8 SFS-EN Optical fibre cables. Part 1-1: Generic specification. General SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN Optical fibre cables. Part 2-10: Indoor optical fibre cables. Family specification for simplex and duplex cables Part 100: General Part 201: General tests. Measurement of insulation thickness Part 202: General tests. Measurement of thickness of non-metallic sheath Part 203: General tests. Measurement of overall dimensions Part 301: Electrical tests. Measurement of the permittivity at 23 C of filling compounds Part 302: Electrical tests. Measurement of the d.c. resistivity at 23 C and 100 C of filling compounds Part 401: Miscellaneous tests. Thermal ageing methods. Ageing in an air oven Part 402: Miscellaneous tests. Water absorption tests Part 403: Miscellaneous tests. Ozone resistance test on cross-linked compounds Part 404: Miscellaneous tests. Mineral oil immersion tests for sheaths Part 405: Miscellaneous tests. Thermal stability test for PVC insulations and PVC sheaths Part 406: Miscellaneous tests. Resistance to stress cracking of polyethylene and polypropylene compounds Part 407: Miscellaneous tests. Measurement of mass increase of polyethylene and polypropylene compounds Part 408: Miscellaneous tests. Long-term stability test of polyethylene and polypropylene compounds Part 409: Miscellaneous tests. Loss of mass test for thermoplastic insulations and sheaths Part 410: Miscellaneous tests. Test method for copper-catalyzed oxidative degradation of polyolefin insulated conductors Part 411: Miscellaneous tests. Low-temperature brittleness of filling compounds Part 412: Miscellaneous tests. Thermal ageing methods. Ageing in an air bomb Part 501: Mechanical tests. Tests for determining the mechanical properties of insulating and sheathing compounds Part 502: Mechanical tests. Shrinkage test for insulations SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN Part 503: Mechanical tests. Shrinkage test for sheaths Part 504: Mechanical tests. Bending tests at low temperature for insulation and sheaths Part 505: Mechanical tests. Elongation at low temperature for insulations and sheaths Part 506: Mechanical tests. Impact test at low temperature for insulations and sheaths Part 507: Mechanical tests. Hot set test for cross-linked materials Part 508: Mechanical tests. Pressure test at high temperature for insulation and sheaths Part 509: Mechanical tests. Test for resistance of insulations and sheaths to cracking (heat shock test) Part 510: Mechanical tests. Methods specific to polyethylene and polypropylene compounds. Wrapping test after thermal ageing in air Part 511: Mechanical tests. Measurement of the melt flow index of polyethylene compounds Part 512: Mechanical tests. Methods specific to polyethylene and polypropylene compounds. Tensile strength and elongation at break after conditioning at elevated temperature Part 513: Mechanical tests. Methods specific to polyethylene and polypropylene compounds. Wrapping test after conditioning Part 601: Physical tests. Measurement of the drop point of filling compounds Part 602: Physical tests. Separation of oil in filling compounds Part 603: Physical tests. Measurement of total acid number of filling compounds Part 604: Physical tests. Measurement of absence of corrosive components in filling compounds Part 605: Physical tests. Measurement of carbon black and/or mineral filler in polyethylene compounds Part 606: Physical tests. Methods for determining the density Part 607: Physical tests. Test for the assessment of carbon black dispersion in polyethylene and polypropylene Non-cellulosic papers for electrical purposes. Part 1: Definitions and general requirements Non-cellulosic papers for electrical purposes. Part 3: Specifications for individual materials. Sheet 3: Unfilled aramid (aromatic polyamide) papers SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2012 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit

9 SFS-EN /A1 Miscellaneous lampholders. Part 2-2: Particular requirements. Connectors for LED modules SFS-EN /A1 Winding wires. Test methods. Part 5: Electrical properties SFS-EN SFS-EN SFS-EN SFS-EN /A13 Short-circuit currents. Calculation of effects. Part 1: Definitions and calculation methods Connectors for optical fibres and cables. Part 1: Generic specification Connectors for optical fibres and cables. Part 1-1: Blank detail specification Electrical accessories. Circuit breakers for overcurrent protection for household and similar installations. Part 1: Circuit-breakers for a.c. operation SFS-EN 60901/A5 Single-capped fluorescent lamps. Performance specifications SFS-EN /A1 SFS-EN /A2 SFS-EN /A13 SFS-EN /A14 SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN Low-voltage switchgear and controlgear. Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units Low-voltage switchgear and controlgear. Part 4-3: Contactors and motor-starters. AC semiconduction and contactors for non-motor loads Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB s). Part 1: General rules Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO s). Part 1: General rules Safety requirements for electrical equipment for measurement, control, and laboratory use. Part 2-033: Particular requirements for hand-held multimeters and other hand-held meters, for domestic and professional use, capable of measuring mains voltage Safety of transportable motor-operated electric tools. Part 2: Particular requirements for planers and thicknessers Safety of transportable motor-operated electric tools. Part 2-5: Particular requirements for band saws Safety of transportable motor-operated electric tools. Part 2-12: Particular requirements for threading machines Terminal markings for valve device stacks and assemblies and for power conversion equipment Part 3-12: Data link layer service definition. Type 12 elements Part 3-14: Data link layer service definition. Type 14 elements Part 3-19: Data link layer service definition. Type 19 elements Part 3-21: Data link layer service definition. Type 21 elements Part 3-22: Data link layer service definition. Type 22 elements Part 4-2: Data-link layer protocol specification. Type 2 elements Part 4-3: Data-link layer protocol specification. Type 3 elements Part 4-11: Data-link layer protocol specification. Type 11 elements Part 4-12: Data-link layer protocol specification. Type 12 elements SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN Part 4-14: Data-link layer protocol specification. Type 14 elements Part 4-18: Data-link layer protocol specification - Type 18 elements Part 4-19: Data-link layer protocol specification. Type 19 elements Part 4-21: Data-link layer protocol specification. Type 21 elements Part 4-22: Data-link layer protocol specification - Type 22 elements Part 5-2: Application layer service definition. Type 2 elements Part 5-3: Application layer service definition. Type 3 elements Part 5-10: Application layer service definition. Type 10 elements Part 5-12: Application layer service definition. Type 12 elements Part 5-14: Application layer service definition. Type 14 elements Part 5-15: Application layer service definition. Type 15 elements Part 5-18: Application layer service definition. Type 18 elements Part 5-19: Application layer service definition. Type 19 elements Part 5-20: Application layer service definition. Type 20 elements Part 5-21: Application layer service definition. Type 21 elements Part 5-22: Application layer service definition. Type 22 elements Part 6-2: Application layer protocol specification. Type 2 elements Part 6-3: Application layer protocol specification. Type 3 elements Part 6-9: Application layer protocol specification. Type 9 elements Part 6-10: Application layer protocol specification - Type 10 elements Part 6-12: Application layer protocol specification. Type 12 elements Part 6-14: Application layer protocol specification. Type 14 elements Part 6-15: Application layer protocol specification. Type 15 elements Part 6-18: Application layer protocol specification. Type 18 elements Part 6-19: Application layer protocol specification. Type 19 elements SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2012 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit

10 SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN 61181/A1 Part 6-20: Application layer protocol specification. Type 20 elements Part 6-21: Application layer protocol specification. Type 21 elements Part 6-22: Application layer protocol specification. Type 22 elements Maritime navigation and radiocommunication equipment and systems. Digital interfaces. Part 450: Multiple talkers and multiple listeners. Ethernet interconnection Mineral oil-filled electrical equipment. Application of dissolved gas analysis (DGA) to factory tests on electrical equipment SFS-EN Single-capped fluorescent lamps. Safety specifications SFS-EN Radiotherapy equipment coordinates, movements and scales SFS-EN Live working. Saddles, stick clamps and their accessories SFS-EN SFS-EN SFS-EN SFS-EN Adaptors for fibre optic connectors. Part 1: Generic specification Adaptors for fibre optic connectors. Part 1-1: Blank detail specification Optical amplifiers. Test methods. Part 4-1: Gain transient parameters. Two-wavelength method Optical amplifiers. Test methods. Part 4-2: Gain transient parameters. Broadband source method SFS-EN Optical amplifiers. Part 2: Digital applications. Performance specification template SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN Optical amplifiers. Part 4: Multichannel applications. Performance specification template Basic test and measurement procedures. Part 3-7: Examinations and measurements. Wavelength dependence of attenuation and return loss of single mode components Basic test and measurement procedures. Part 3-28: Examinations and measurements. Transient loss Basic test and measurement procedures. Part 3-33: Examinations and measurements. Withdrawal force from a resilient alignment sleeve using gauge pins Basic test and measurement procedures. Part 3-39: Examinations and measurements. Physical Contact (PC) optical connector reference plug selection for return loss measurements Fibre optic fan-outs. Part 1: Generic specification Fibre optic fan-outs. Part 1-1: Blank detail specification Lamp controlgear. Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps Lamp controlgear. Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) SFS-EN Convertor transformers. Part 1: Transformers for industrial applications SFS-EN Conduit systems for cable management. Part 25: Particular requirements. Conduit fixing devices SFS-EN Low-voltage switchgear and controlgear assemblies. Part 5: Assemblies for power distribution in public networks SFS-EN Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Equipment for testing, measuring or monitoring of protective measures. Part 13: Hand-held and hand-manipulated current clamps and sensors for measurement of leakage currents in electrical distribution systems SFS-EN SFS-EN SFS-EN SFS-EN Safety of transformers, reactors, power supply units and combinations thereof. Part 2-9: Particular requirements and tests for transformers and power supply units for class III handlamps for tungsten filament lamps Safety of transformers, reactors, power supply units and combinations therof. Part 2-12: Particular requirements and tests for constant voltage transformers and power supply units for constant voltage Safety of transformers, reactors, power supply units and combinations thereof. Part 2-15: Particular requirements and tests for isolating transformers for the supply of medical locations Safety of transformers, reactors, power supply units and combinations thereof. Part 2-20: Particular requirements and tests for small reactors SFS-EN Salt mist corrosion testing of photovoltaic (PV) modules SFS-EN SFS-EN /A1 Electronic components. Reliability. Reference conditions for failure rates and stress models for conversion Photovoltaic (PV) module safety qualification. Part 1: Requirements for construction SFS-EN /A1 Photovoltaic (PV) module safety qualification. Part 2: Requirements for testing SFS-EN SFS-EN SFS-EN SFS-EN /A1 Performance standard. Part 087-6: Non-connectorised single-mode bidirectional 1310 nm upstream and 1490 nm downstream WWDM devices for category O. Uncontrolled environment Fibre optic connector interfaces. Part 28: Type LF3 connector family Fibre optic connector interfaces. Part 29: Type BLINK connector series Fibre optic connector optical interfaces. Part 3-6: Optical interface. 2,5 mm and 1,25 mm diameter cylindrical 8 degrees angled-pc composite ferrule using Cu-Ni-alloy as fibre surrounding material, single mode fibre SFS-EN Fibre optic sensors. Part 1: Generic specification SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN SFS-EN Industrial communication networks. Profiles. Part 5-2: Installation of fieldbuses. Installation profiles for CPF Industrial communication networks. Profiles. Part 5-3: Installation of fieldbuses. Installation profiles for CPF Industrial communication networks. Profiles. Part 5-4: Installation of fieldbuses. Installation profiles for CPF Industrial communication networks. Profiles. Part 5-6: Installation of fieldbuses. Installation profiles for CPF Industrial communication networks. Profiles. Part 5-10: Installation of fieldbuses. Installation profiles for CPF Industrial communication networks. Profiles. Part 5-11: Installation of fieldbuses. Installation profiles for CPF Industrial communication networks. Profiles. Part 5-12: Installation of fieldbuses. Installation profiles for CPF Industrial communication networks. Profiles. Part 5-14: Installation of fieldbuses. Installation profiles for CPF SESKOn alueelta julkaistut ja vahvistetut SFS-standardit 2012 SESKOn alueelta julkaistut ja vahvistetut SFS-standardit